Emtek Contemporary Trinity Pull gives you a defined modern gripping point for cabinet and furniture fronts, using a 6 inch center-to-center layout that keeps hole spacing consistent across a run of doors and drawers. The polished chrome finish provides a bright, reflective surface that reads clean and contemporary on finished millwork. As part of Emtek handles and pulls in the decorative hardware and moldings category, this pull organizes hand contact to a single, durable bar so finished surfaces stay cleaner in everyday use. The 6 inch CC dimension follows a common cabinet drilling pattern, which supports straightforward layout on new work or when aligning with an existing grid. The manufacturer part number 86266US26 clearly identifies the polished chrome Trinity design, helping shops and installers match this pull across multiple rooms or phased projects without mix-ups.
The 6 inch CC mounting dimension on this Emtek Trinity cabinet pull defines the distance between the two mounting points, guiding drill patterns for both new layouts and replacements using that same spread. Because the pull is specified as part of handles and pulls hardware, it is designed for through-bored cabinet and furniture fronts where a rigid connection is needed. The center-to-center callout lets installers build or adjust templates once and reuse them across a project, supporting uniform alignment from door to door. The polished chrome finish on the N/D brass Trinity Pull is intended for exposed mounting locations, so careful positioning along the 6 inch CC line helps keep sightlines straight and visually consistent.
The Emtek Contemporary Trinity Pull, 6 inch CC, Polished Chrome - 86266US26 is suited to cabinet and furniture fronts where a linear pull matches the design intent. Its placement in decorative hardware and moldings under handles and pulls defines it as a visible touchpoint on casework, not a concealed component. The 6 inch CC measurement aligns with projects that are laid out around that specific center-to-center spacing, from kitchen runs to built-in storage units. Because the Trinity design is identified in both the SAP description and web description as a pull, it is configured for everyday gripping on doors and drawers that require a firm, repeatable grab point.
The 6 inch CC callout on this Trinity pull drives both initial layout and later replacement, since the fixed center-to-center distance dictates where holes are bored in the panel. Using a pull defined as N/D BRS TRINITY PULL 6 C-C US26 keeps the part number, finish, and drilling pattern tied together, which helps maintain consistency when hardware is changed or expanded in stages. The polished chrome US26 designation keeps finish selection unambiguous, so installers matching existing hardware can rely on the 86266US26 code for continuity. Because the product is classified under handles and pulls, it is meant to carry the routine load of opening and closing cabinetry, and the named Trinity form factor helps shops standardize on one style across multiple rooms for a coordinated layout.
Emtek Contemporary Trinity Pull fits cabinet and furniture fronts where a modern, linear handle from the decorative hardware and moldings, handles and pulls category is required.
The 6 inch CC measurement indicates the distance between the two mounting points, guiding drilling and layout so cabinets and drawers share the same hole spacing.
The polished chrome US26 finish creates a bright, reflective surface that coordinates with other chrome hardware, supporting a clean, modern look on visible cabinetry.
Part number 86266US26 uniquely identifies this Emtek Trinity Pull configuration, linking the 6 inch CC size and polished chrome finish for accurate ordering and matching.
This Emtek pull is categorized under decorative hardware and moldings, handles and pulls, indicating it is intended as a visible operating handle on cabinet and furniture fronts.
N/D BRS Trinity Pull 6 C-C US26 describes a Trinity style pull with a 6 inch center-to-center layout and a polished chrome US26 finish, used as a cabinet handle.
The Emtek Contemporary Trinity Pull, 6 inch CC, Polished Chrome - 86266US26 gives cabinet shops and installers a clearly defined handle choice with a fixed 6 inch CC drilling pattern. Its place in the decorative hardware and moldings, handles and pulls category positions it for visible cabinet and furniture fronts where a polished chrome US26 finish is part of the design plan. Using the specific part number 86266US26 ties finish, style, and center-to-center spacing together, supporting consistent selection whenever additional pulls are needed for matching work.