Clip-On Cam Adjustable Wing Mounting Plate, Nickel-Plated, Screw-On, 0mm

Clip-On Cam Adjustable Wing Mounting Plate Use

clip-on cam adjustable wing mounting plate is an economical clip on plate that works with all Salice hinges Series F and Series B, so installers can use one plate style across those hinge lines without changing drilling patterns or hardware strategy. This hinge mounting plate belongs to the hinge base plates category, giving a stable interface between cabinet and hinge arm for consistent door motion. The 0mm mounting plate height keeps the door overlay geometry driven mainly by the hinge arm, which simplifies layout when matching existing Salice setups. Made by Salice America, this plate aligns with Salice hinge design standards for these series. The nickel-plated finish is corrosion resistant, so the plate holds up in typical cabinet environments where humidity and everyday use can otherwise affect bare steel. Lifetime warranty coverage adds long-term assurance for permanent cabinet installations where callbacks are costly.

Key Mounting Plate Details That Support Work

• This economical clip on plate works with all Salice hinges Series F and Series B, so one mounting style can handle multiple hinge models on a job, simplifying planning on larger runs.
• The 0mm plate height keeps the hinge arm geometry predictable, which helps when duplicating existing Salice door overlays or aligning new doors alongside older runs using the same system.
• Nikel-plated, corrosion-resistant construction maintains the integrity of the hinge interface, which matters for door alignment over years of opening and closing in typical cabinet environments.
• Standard 37 mm x 32 mm positioning follows a recognized layout, so drilling patterns can be repeated across cabinets for faster installation and easier jig or line setup.
• Lifetime warranty supports long-term use of this mounting plate, which is important when hinges and plates are installed in permanent cabinetry that is not intended to be revisited.

Hinge Mounting Plate Adjustment And Fit Details

Depth adjustment of -0.5 mm to +2.8 mm is provided by an eccentric cam, so the installer can fine-tune the door position toward or away from the cabinet front after mounting without remounting the plate. Height adjustment of plus or minus 2 mm is handled through slotted holes, so vertical door reveals can be dialed in by shifting the plate position slightly before tightening the screws. This plate is screw-on, meaning the mounting relies on screws to secure it to the cabinet surface, which suits standard cabinet construction techniques that expect mechanical fastening through the plate holes.

Using This Salice Hinge Mount Plate In Cabinets

Where This 0mm Salice Plate Is Applied

This hinge mounting plate is identified as DIECST MTG PLT, SCREW-IN, 0MM, 1 CAM and is classified under hinges and hinge base plates, so it fits into cabinet door hinge assemblies where a Salice hinge connects to the cabinet side. Compatibility with all Salice hinges Series F and Series B means it can serve on a variety of doors using those hinge arms, from standard cabinet runs to projects where multiple door sizes still use these series. The 0mm plate height provides a neutral base level, allowing the chosen hinge arm to determine overlay, which is useful in systems built around Salice geometry. Standard 37 mm x 32 mm positioning aligns with typical drilling layouts, giving a known footprint when working with boring machines, drilling jigs, or pre-bored cabinet components.

How Adjustment And Design Support Repeatable Results

The depth adjustment range of -0.5 mm to +2.8 mm is handled by an eccentric cam, so the door can be brought closer to or further from the cabinet front within that window, helping correct small case or door tolerances without relocating the plate. Height adjustment of plus or minus 2 mm via slotted holes lets the installer slide the mounted plate slightly up or down, which helps align door reveals across a run when cabinet sides or floors vary slightly. The screw-on mounting method secures the plate through its holes, contributing to a stable connection that holds the set adjustments during normal cabinet use. The nickel-plated, corrosion-resistant finish supports consistent operation in environments where moisture and cleaning can otherwise affect exposed metal, helping maintain hinge function and reveal accuracy over time. Because the plate is economical while still covered by a lifetime warranty, it suits both production work and long-term residential or commercial installations where repeated adjustment over the product life can be expected.

Common Questions About This Salice Mount Plate

Selecting This Salice Plate For Your Hinge Work

This Salice America clip-on cam adjustable wing mounting plate combines 0mm height, screw-on mounting, and compatibility with all Salice hinges Series F and Series B, so it fits standard cabinet workflows built around these hinges. Depth adjustment from -0.5 mm to +2.8 mm by eccentric cam, plus or minus 2 mm height adjustment through slotted holes, provides the fine control needed to align doors cleanly without reboring. Nickel-plated, corrosion-resistant construction and a lifetime warranty support long-term cabinet installations where stable hinge performance and repeatable adjustment matter.