Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Amerock Divinity 3 in pull gives a cabinet or drawer a defined grip point using a 3 in (76 mm) center-to-center mounting layout, which helps align multiple handles accurately across doors and drawers. The pull uses a zinc die-cast construction, which provides a solid-feeling handle that holds up under everyday opening and closing. A satin nickel finish on the pull presents a neutral metal tone that works with many cabinet colors while keeping reflections subdued in work areas. The handle length of 4-9/16 in (116 mm) gives fingers space at each end beyond the mounting screws, helping users grab it from different angles. A projection of 1-1/4 in (32 mm) stands the pull off the door or drawer face, leaving room behind for fingers to wrap without rubbing the surface. The 1/2 in (13 mm) width creates a slim front profile, which helps when coordinating with other narrow decorative hardware.
The 3 in (76 mm) center-to-center measurement defines where the mounting holes land, which is useful when aligning with existing 3 in drill patterns on cabinet doors and drawers. With a 4-9/16 in (116 mm) length, the pull reaches past each side of the mounting points, helping cover minor tear-out around old holes. The 1-1/4 in (32 mm) projection determines how far the handle stands off the front, which guides drilling depth and placement when setting up for comfortable finger clearance. A 1/2 in (13 mm) width concentrates the load along a slim footprint, which matters when positioning the pull on narrow rails or stile locations. The satin nickel finish ties into surrounding decorative hardware, which aids installers planning a consistent visual line across a full cabinet run.
This Amerock Divinity Series 3 in center-to-center pull serves as a handle for cabinet doors or drawers using the 3 in spacing standard, which matches many existing bored fronts in kitchens, baths, and shop cabinets. The 4-9/16 in (116 mm) length gives enough span for use on both narrow doors and moderate-width drawers, allowing one model to cover multiple locations within the same project. With a 1-1/4 in (32 mm) projection, the pull works on fronts where users need finger room without extending too far into walkways. The 1/2 in (13 mm) width lets the pull sit neatly on face frames or frameless panels, which helps maintain clean lines in both traditional and contemporary layouts.
The defined 3 in (76 mm) center-to-center dimension supports repeatable drilling, which helps installers run a jig across a full bank of cabinets while keeping each pull aligned. The zinc die-cast construction offers a uniform body, which contributes to consistent feel when multiple pulls are used across a project. A satin nickel finish keeps the visual tone steady from piece to piece, which matters when doors and drawers line up in long runs. The 1-1/4 in (32 mm) projection and 1/2 in (13 mm) width shape how hands interact with the hardware, supporting a predictable grip from one cabinet to the next. The overall 4-9/16 in (116 mm) length gives each handle a similar visual weight, which helps maintain balance between small doors and larger drawer fronts when the same pull is repeated.
The Amerock Divinity 3 in pull uses a 3 in (76 mm) center-to-center measurement, which matches standard drilling layouts on many cabinet doors and drawers.
The Amerock Divinity BP19258G10 pull measures 4-9/16 in (116 mm) in overall length, which provides extra handle area beyond the mounting holes for a comfortable grip.
The pull has a 1-1/4 in (32 mm) projection, which sets the handle off the cabinet face to allow finger clearance behind the pull during use.
The Divinity cabinet pull is made from zinc die-cast material, which creates a solid handle body suited to repeated opening and closing cycles.
This Amerock Divinity pull uses a satin nickel finish, which provides a muted metallic look suitable for many cabinet and drawer styles.
The Amerock Divinity Series pull has a 1/2 in (13 mm) width, which gives a slim appearance while still offering a defined gripping surface.
The Amerock Divinity Series 3 in center-to-center satin nickel pull combines a 3 in (76 mm) mounting layout, 4-9/16 in (116 mm) length, and 1-1/4 in (32 mm) projection to support straightforward cabinet and drawer handle installations. The zinc die-cast construction and satin nickel finish give a consistent look and feel across multiple fronts in the same project. For work calling for a slim, 1/2 in (13 mm) wide pull that matches 3 in drilling, this model offers dimensions aimed at repeatable layout and a uniform appearance.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  AMBP5261-PWT Mfr# BP5261PWT | Amerock Divinity Pewter 1-1/4" (32 mm) Diameter Knob, BP5261PWT |
