Wurth Truss Head Screw For Hinge And Slide Work
Wurth #8 x 7/16 truss head screw is a low truss head screw designed for use on ball bearing slides such as KV and Accuride, so it fits common slide work in cabinet projects. The sharp point coarse thread design lets the screw bite quickly into typical woodworking materials, which speeds up hinge and drawer slide installation. The white finish on this truss head screw matches white hardware and casework, helping installations blend into light interiors. A #2 Phillips drive matches standard Phillips drive bits, so installers can run these screws with common drivers. The short 7/16 inch length suits many slide and hinge mounting situations where extra length is not needed, supporting clean fastening without excess projection.
Key Installation Details For Fastener Selection
- The low truss head profile provides broad bearing under the head, which helps spread load on hinges and ball bearing slides while keeping a low projection inside the cabinet.
- The screw is described for use on ball bearing slides such as KV and Accuride, so it matches typical drawer slide mounting geometry found in many cabinet lines.
- The sharp point coarse thread pattern is geared to biting quickly into material, which supports faster driving with reduced walking at the start of the screw.
- The white finish coordinates with white slides and hinges where used, helping fasteners visually blend with light-colored components and interiors.
- The screw uses #2 Phillips drive bits, allowing installers to use standard bits they likely already carry for consistent driving and reduced bit changes.
Practical Drive And Fastening Characteristics
This hinge and drawer slide installation screw uses a #2 Phillips drive, so the bit engages in a familiar recess that supports controlled torque on slides and hinges. The sharp point combined with coarse thread lets the screw start quickly and pull down hardware in fewer turns, which is useful during repetitive ball bearing slide or hinge runs. Its low truss head shape offers broad contact against slide or hinge flanges while sitting relatively flat, which helps reduce snag points inside drawers or cabinets. The white finish on the truss head presents a consistent look against white or light-colored hardware components, supporting neat visual results on exposed or semi-exposed mounts.
Using This Screw In Drawer And Hinge Runs
Where This Truss Head Screw Is Typically Applied
The low truss head screw is described for use on ball bearing slides such as KV and Accuride, so it aligns with applications where slides rely on flat-head bearing against slotted or round mounting holes. In drawer work, the #8 x 7/16 inch size suits many slide brackets and direct-to-cabinet slide installations where only moderate penetration is needed into the cabinet side. For hinge work, the truss head and coarse thread give broad clamping and secure bite into common cabinet substrates, which helps keep hinge plates stable under repeated door cycles. The white finish lets the screw visually coordinate with white slides and matching components, so drawer interiors or hinge zones maintain a consistent color where the head remains visible.
Details That Support Consistent Mounting Results
The #2 Phillips drive specified for this screw works with standard Phillips drive bits, giving installers a familiar feel and reliable engagement during repeated hinge and slide fastening. The sharp point coarse thread design lets the screw advance rapidly once started, which reduces time spent driving each fastener in long banks of ball bearing slides. The low truss head offers wide bearing under the head, improving the way slides and hinges clamp to mounting surfaces and supporting alignment retention under load. Case hardened construction, as stated in the description, provides a hardened fastener body that resists head deformation during driving, which is helpful when running many screws with powered drivers. Together, these traits give a screw suited to repetitive hinge and ball bearing slide mounting in cabinet and drawer projects.
Common Questions About This Wurth Truss Head Screw
What applications is this Wurth hinge and drawer slide screw described for?
This Wurth low truss head screw is described for use on ball bearing slides such as KV and Accuride, which positions it for typical cabinet drawer slide and related hardware installations.
What size and head style does this installation screw use?
The screw is described as #8 x 7/16 inch with a low truss head, giving a short length and broad head bearing surface suited to slide and hinge flanges.
How is this ball bearing slide installation screw driven?
The screw uses #2 Phillips drive bits, so it works with common Phillips drivers used in cabinet and drawer slide installation work.
What point and thread type does this white truss head screw have?
The screw is specified with a sharp point coarse thread, helping it start quickly and pull into typical cabinet materials during hinge and slide mounting.
What finish is noted for this Wurth truss head screw?
The description notes a white finish is available, which aligns with white hardware and interiors where a matching screw head appearance is desired.
How does the case hardened description affect screw performance?
The screw is described as case hardened, indicating a hardened surface that supports head and drive integrity when driven with power tools.
Selecting This Screw For Slide And Hinge Jobs
The Wurth #8 x 7/16 truss head hinge and drawer slide installation screw combines a low truss head, #2 Phillips drive, and sharp point coarse thread specifically described for ball bearing slides such as KV and Accuride. That blend suits repetitive cabinet hinge and drawer slide fastening where broad head bearing, quick starting, and a white finish support both installation speed and finished appearance. For projects built around ball bearing slides and matching hardware, this screw offers a focused option for fastening those components to cabinet structures.
