Würth #8 x 7/16" Truss Head Hinge and Drawer Slide Installation Screw Phillips Drive - Sharp Point Coarse Thread Zinc, 3670000235961 5000 - 5000/Box

#8 Truss Head Screw For Hinge And Slide Work

#8 x 7/16 truss head screw describes a low truss head fastener sized for hinge and drawer slide installation where a broad bearing surface helps clamp hardware without biting too deeply into the material. The sharp point coarse thread cuts into common cabinet substrates quickly, so driving goes faster and the screw pulls components together firmly. The Phillips drive works with standard #2 Phillips drive bits, keeping bit choice simple across the job. The zinc finish provides a standard plated surface commonly used on interior hardware, which supports a consistent look with zinc finished ball bearing slides. The screw is listed for use on ball bearing slides such as KV and Accuride, so it matches the head style and shank configuration typically preferred for those slide types.

Key Screw Details That Support Fast Hardware Work

• The low truss head profile spreads load across a wider area, helping hold ball bearing slides and similar hardware flat against the mounting surface.
• The #8 shank size and 7/16 inch length pair thread engagement with a compact length that helps reduce breakthrough risk in cabinet parts.
• The sharp point coarse thread design bites into material quickly, which helps screws start cleanly and seat hardware without pre-tapping.
• The zinc finish matches many zinc-finished slides and hinges, which helps keep hardware appearance and component selection consistent.
• The Phillips drive is designed for #2 Phillips drive bits, so installers can run the same bit style across hinges and drawer slides.

Installation Behavior Of This Phillips Drive Screw

The sharp point on this screw starts into the substrate with minimal pressure, so driving into cabinet parts is direct. The coarse thread form advances quickly through the material, pulling slide and hinge flanges tight with fewer turns. The low truss head geometry provides a broad underside that sits against hardware slots, which helps clamp the metal without deforming narrow flanges. Because the head is described as Phillips, it works with standard #2 Phillips drive bits, streamlining bit selection when running fasteners on casework or drawers. The 7/16 inch length works with many drawer slide and hinge mounting zones where a relatively short screw is needed.

Using This Screw With Slides And Cabinet Hardware

Hinge And Drawer Slide Mounting Applications

The web description identifies this as a low truss head screw for use on ball bearing slides such as KV and Accuride, so it aligns with the head and shank style widely used on those slide families. The #8 diameter pairs with typical clearance holes in slide and hinge mounting flanges, supporting firm clamping without excessive play. The 7/16 inch length is suited to many cabinet side and drawer side thicknesses used with ball bearing slides, helping anchor the hardware while keeping penetration depth controlled. Because the same screw is referenced for hinge and drawer slide installation, it can be used across multiple hardware positions in a cabinet run.

Details That Support Consistent Fastener Results

The case hardened construction described in the web content gives the screw a hardened surface, which supports bit grip at the drive recess during installation. This hardened exterior works with the Phillips drive design so #2 Phillips drive bits can transmit torque without quickly rounding the recess. The low truss head shape presents a wide underside bearing area, so when torque is applied, clamping pressure is spread across more of the slide or hinge flange. The zinc finish contributes a smooth plated surface, which helps the head seat consistently against plated hardware. The combination of coarse thread and sharp point helps every screw start and drive in a similar way, supporting repeatable mounting depth across a run of cabinets or drawers.

Common Questions About This Wurth #8 Screw

Selecting This Screw For Slide And Hinge Jobs

This Wurth #8 x 7/16 truss head hinge and drawer slide installation screw combines a low truss head, sharp point coarse thread, and zinc finish with a Phillips drive sized for #2 Phillips bits. Those details support ball bearing slide work such as KV and Accuride and also align with typical hinge mounting needs. For cabinet and drawer projects that call for a low truss head, case hardened zinc screw in this size, this part number provides that configuration.