Wurth Washer Head Hinge Screw For Precise Mounting
Wurth washer head hinge screw is a #8 x 3/4 inch edge application screw designed for mounting hardware into or near the edge of hardwood material. The web description states that these edge application screws are designed to prevent splitting in hardwoods when hardware is attached into or near the edge of the material, which supports cleaner work around exposed cabinet edges. The screw is described as a washer head hinge and drawer slide installation screw, so it handles both hinge plates and drawer slides in typical cabinet construction. The product description specifies a combo drive that uses #2 square drive bits for insertion and #2 Phillips drive bits for aftermarket adjustment, so installers can drive fasteners quickly in production and still fine-tune later with common Phillips drivers. The screw is case hardened, so it supports driving into hardwoods during hinge and slide installation.
Key Details That Support Edge Hardware Work
- The web description identifies these as edge application screws designed to prevent splitting in hardwoods when hardware is attached into or near the edge of the material, helping protect narrow stiles and rails during hinge and drawer hardware installation.
- The product is described as a washer head hinge and drawer slide installation screw, so one fastener style addresses both hinge plates and drawer slide brackets, simplifying jobsite inventory and matching hardware rows along the cabinet side.
- The description notes that the screw uses #2 square drive bits for insertion, allowing positive bit engagement during production driving when mounting European style face frame hinges, pin and pivot hinges, or catches and latches referenced in the web description.
- The same description specifies #2 Phillips drive bits for aftermarket adjustment, so service work or small alignment tweaks can be handled quickly with a common Phillips screwdriver without changing to square bits after installation.
- The product information states that the screws are case hardened, so the fastener body is designed for driving into hardwood cabinet components where hinge and drawer slide screws see repeated loads and torque during installation.
- The SAP description identifies the screw as coarse thread and lubricated, which supports driving into hardwoods with less resistance, helping fasteners pull hardware plates tight to the surface while reducing driving effort.
Installation Behavior Of This Combo Drive Screw
The web description explains that these edge application screws are designed to prevent splitting in hardwoods when hardware is attached into or near the edge of the material, so they support cleaner mounting of hinges and latches along narrow cabinet edges. The product description calls out use with European style face frame hinges, pin and pivot hinges, or with catches and latches, so the same screw style handles common cabinet and furniture hardware installations. The mention of #2 square drive bits for insertion means production driving can rely on square bits that resist cam-out while setting multiple screws in a hinge row. After hardware is installed, #2 Phillips drive bits for aftermarket adjustment let installers tweak hinge or catch position during service without swapping to a square bit.
How This Edge Application Screw Performs In Use
Where This Hinge And Slide Screw Is Applied
The web description states that these edge application screws are used when hardware is attached into or near the edge of hardwood material, so they are suited to cabinet doors, face frames, and carcass edges where splitting risk is higher. The same description states that they are used with European style face frame hinges, pin and pivot hinges, or with catches and latches, so a single screw pattern can be used across door hinges, specialty hinges, and closure hardware on the same project. The product name describes them as washer head hinge and drawer slide installation screws, which ties their use directly to mounting drawer slides in addition to the hinge and latch hardware cited in the description. This allows hardware rows along cabinet sides and frames to share a consistent fastener style for a uniform appearance.
Why The Type 17 Coarse Thread Design Matters
The SAP description identifies the screw as CRS,RNDWSH,RECEX T17,LUB and the web description lists them as edge application screws designed to prevent splitting in hardwoods when hardware is attached into or near the edge of the material, so the type 17 auger point and coarse thread work together to help the screw enter hardwood with less splitting at the edge. The same SAP description notes that the screw is lubricated, so driving torque is reduced as coarse threads cut into hardwood, helping plates and slides draw tight to the surface with smoother insertion. The product information labels the screw as case hardened, which means the fastener body is prepared for the repeated loads of mounting hinges and drawer slides into dense cabinet materials. The combo drive design described in the web text, using #2 square drive bits for insertion and #2 Phillips drive bits for aftermarket adjustment, means installers can rely on square drive for initial installation and still perform later adjustments with a standard Phillips driver on hinge or latch screws. Together, these verified features support consistent mounting, reduced edge damage in hardwoods, and easier service adjustments on completed cabinetry.
Common Questions About This Wurth Edge Screw
What hardware is this Wurth washer head hinge screw used with?
The web description states it is used with European style face frame hinges, pin and pivot hinges, or with catches and latches, so it covers typical cabinet door and closure hardware.
How does this edge application screw help in hardwood edges?
The description explains that these edge application screws are designed to prevent splitting in hardwoods when hardware is attached into or near the edge of the material during installation.
Why does this screw use both square and Phillips drives?
The product information notes #2 square drive bits for insertion and #2 Phillips drive bits for aftermarket adjustment, supporting fast driving in production and simple adjustments later.
Is this hinge and drawer slide screw suitable for hardwood cabinets?
The web description specifies hardwood use and notes the screws are case hardened and designed to prevent splitting in hardwoods at or near the edge.
What does coarse thread lubricated mean for installation?
The SAP description calls the screw coarse thread and lubricated, which supports easier driving and seating when cutting into hardwood cabinet components.
Can this screw be used for drawer slide installation?
The product name describes it as a washer head hinge and drawer slide installation screw, so it is intended for both hinge plates and drawer slide mounting.
Selecting This Screw For Edge Hardware Tasks
The product name, SAP description, and web description together define this Wurth #8 x 3/4 inch washer head hinge and drawer slide installation screw as a case hardened, coarse thread, lubricated edge application fastener designed to prevent splitting in hardwoods when hardware is mounted into or near the edge. The ability to use #2 square drive bits for insertion and #2 Phillips drive bits for aftermarket adjustment supports both production work and follow-up service on European style face frame hinges, pin and pivot hinges, catches, and latches. When an installation calls for hinge, drawer slide, and closure hardware into hardwood cabinet edges, these verified characteristics support consistent mounting results.
