A 3/4-Inch Hinge and Drawer Slide Screw Built for Thin Cabinet Panels
This Würth #8 x 3/4-inch truss head screw is designed for mounting European cup hinges, drawer slides, and other cabinet hardware to panel stock without over-penetrating the material. The short length keeps the screw within the panel, the wide truss head distributes clamping load across the hardware mounting plate, and the Type 17 auger point starts cleanly in wood-based substrates.
Key Features
- Truss head profile delivers a wide, low-profile bearing surface that spans hardware mounting plate holes without a separate washer.
- Combination Phillips and square drive accepts a #2 Phillips or a #2 square bit in the same recess for flexibility on the bench or at the job site.
- Type 17 auger point cuts into particleboard, MDF, and solid wood quickly, reducing the torque needed to seat the screw.
- Coarse thread grips the fiber structure of particleboard, MDF, and plywood cabinet panels for strong pull-out resistance.
- Zinc finish provides standard corrosion protection suited to dry interior cabinet environments.
- 1,000 screws per box keeps the supply in step with production-volume hardware installation.
Where the 3/4-Inch Length Does Its Job
Hardware mounting in cabinetry often demands a short screw. When hinge mounting plates, drawer slide brackets, and cabinet hardware clips are fastened to 3/4-inch panels, a longer screw risks punching through to the visible face. The 3/4-inch length on this screw is matched to those conditions: enough thread engagement to hold the hardware securely, short enough to stay well within standard panel thickness. It is the right call for side-mount drawer slide installation, European hinge clip plates, and any hardware fitting where the mounting hole is shallow and a longer fastener would be a liability.
Truss Head, Combo Drive, and Type 17 Point
The truss head sits low and spreads its bearing surface broadly, which is exactly what hardware mounting plates need. Rather than concentrating load at a small contact ring as a pan head would, the wide truss profile bridges across the slotted openings in hinge plates and slide brackets. The combination recess accepts a #2 Phillips or #2 square bit, so the installer is not locked into a single driver. The square recess is designed to hold the screw on a correctly sized bit for one-handed placement, which matters when the other hand is holding a hinge against the cabinet face. The Type 17 auger point reduces driving torque and clears chips from the hole as the screw advances, which helps in the particleboard and MDF used throughout most cabinet carcasses.
Who Reaches for This Screw
Cabinet shops installing European-style hinges and undermount or side-mount drawer slides will go through these in quantity. The 1,000-count box is sized for that reality. Finish carpenters and installers doing site work on frameless or face-frame cabinets will find the short length and combo drive practical when working in tight spaces where switching bits costs time. The zinc finish is appropriate for the dry interior environments where cabinet hardware lives.
Common Questions
Why use a truss head instead of a pan head for hinge and drawer slide mounting?
The truss head has a larger diameter than a standard pan head, so it spans the slotted openings and wider holes in hinge mounting plates and drawer slide brackets without pulling through. That wider bearing surface distributes the clamping load more evenly across the hardware fitting.
Will a standard #2 Phillips bit work in this screw?
Yes. The combination recess accepts both a #2 Phillips and a #2 square bit. Either will drive the screw; the square recess holds the screw on a correctly sized bit for one-handed placement when that matters.
Is 3/4 inch the right length for standard 3/4-inch cabinet panels?
For most hinge and drawer slide hardware mounted to a 3/4-inch panel face, yes. The screw engages the panel firmly without breaking through the opposite face. If you are mounting through a thicker substrate or need more pull-out depth, a longer screw in the same family is the better choice.
Is this screw suitable for particleboard and MDF cabinet panels?
Yes. The coarse thread and Type 17 auger point are both well suited to particleboard, MDF, and plywood. The coarse thread grabs the fiber matrix of engineered panels effectively, and the Type 17 point clears chips as it drives rather than compressing material ahead of the tip.
Can this screw be used for outdoor or high-humidity applications?
The zinc finish is suited to dry interior environments. For applications with regular moisture exposure, a screw with a heavier corrosion-resistant coating is a better fit.
The Right Screw for the Hardware Bay
When the job is mounting hinges and drawer slides to standard cabinet panels, this 3/4-inch Würth truss head screw keeps the installation clean, the hardware seated flat, and the box stocked for the volume that cabinet work demands.
