14" RV485 Heavy-Duty Double Slot Shelf Bracket, Satin Zinc Finish

14 Inch Heavy Duty Double Slot Shelf Bracket Use

14 inch heavy duty double slot shelf bracket describes a Reeve Store Equipment Company RV485 bracket designed as a shelf support in shelving runs. The 14 inch length gives mid-depth support for typical storage or display shelves, which helps distribute load without overhanging the front edge. The double slot design is typically used with the RV44 series standard, so the bracket engages securely into that upright system for stable vertical alignment along the run. This bracket is part of a shelf standards and brackets system, which lets installers build adjustable shelving layouts in closets, garages, or commercial runs. As a heavy-duty bracket, it serves applications that need higher load capacity per pair, which matters when planning deeper shelving or denser storage.

Key RV485 Shelf Bracket Details For Projects

• The Reeve Model RV485 designation ties this bracket to the RV485 series, helping installers match it with the correct RV44 series standard for consistent fit across a shelving run.
• The 14 inch length supports shelves sized for that projection, so shelf depth and bracket length stay aligned and reduce stress at the rear standard connection during loading.
• The material is 1/16 inch thick cold rolled steel, which provides a rigid support profile under load and helps keep long shelving straight over time in typical storage conditions.
• The satin zinc finish, described as Brillatone zinc, gives the steel surface a finished appearance while separating bare steel from the environment in normal indoor shelving installations.
• The bracket has two engagement teeth to fasten the standard to the bracket, which reinforces the connection in the upright slots and helps resist dislodging during shelf loading or adjustment.
• A shelf lip at the end of the bracket supports the front edge of the shelf, helping keep the shelf seated on the bracket and reducing forward slip during everyday use.
• The design is noted for use in long runs of shelving, which suits applications where multiple brackets and standards are installed in series to support continuous shelves along a wall.
• The weight rating is 335-710 lb per pair based on length, so within that series installers can match bracket length to expected loading needs when laying out heavier storage or display shelves.

RV485 Shelf Bracket Fit And Standard Engagement

The RV485 model is typically used with the RV44 series standard, so the bracket profile and engagement teeth are configured for that standard pattern. This pairing provides a predictable fit between upright and bracket along the full system height. The double slot layout works within the RV44 standard to locate the two engagement teeth, which helps maintain alignment when multiple brackets are set at the same elevation. The two engagement teeth fasten the standard to the bracket, creating a fixed connection point that resists vertical slip in the slots during loading. The shelf lip at the end of the bracket then supports the front edge of the shelf, translating that stable connection into a consistent, level support plane across each shelf span.

Using The 14 Inch RV485 Bracket In Runs

Where This Double Slot Shelf Bracket Fits Best

The RV485 double slot shelf bracket is part of a shelf, closet, and garage organization category, so it serves storage and organization runs using standards and brackets. Being described for use in long runs of shelving, it suits layouts where shelves extend across several uprights, such as wall-length garage storage or continuous retail shelving. The 14 inch length positions it among the available RV485 lengths from 8 inch through 24 inch, so it occupies a middle range suitable for moderate-depth shelving. The bracket is designed for use with the RV44 series standard, tying its fit and slot engagement to that standard line so all supports in the run share the same interface.

Details That Support Load And Repeatable Alignment

The 1/16 inch thick cold rolled steel construction gives the 14 inch RV485 bracket a solid support section, which is important when building shelves that will carry significant distributed loads in a storage aisle or closet. The weight rating of 335-710 lb per pair, based on length, characterizes the heavy-duty intent of this bracket series and allows planners to select brackets within that range for demanding applications. The two engagement teeth that fasten the standard to the bracket create a dual-point lock into the RV44 series standard, which helps each bracket hold its set height and resist rocking under load. The shelf lip at the end of the bracket provides a defined support line under the front of the shelf, which stabilizes shelf boards and helps maintain a consistent plane. The satin zinc finish, described as Brillatone zinc, covers the cold rolled steel surface, offering a clean, uniform appearance in open storage areas while protecting the base metal in typical indoor environments.

Buyer Questions About The RV485 14 Inch Bracket

Select The 14 Inch RV485 Bracket For Heavy Runs

The 14 inch RV485 heavy-duty double slot shelf bracket from Reeve Store Equipment Company combines a defined 14 inch reach, 1/16 inch thick cold rolled steel construction, and double engagement teeth for use with the RV44 series standard. Its weight rating of 335-710 lb per pair across the series reflects a heavy-duty role in long shelving runs, while the shelf lip at the end supports shelf edges where loads are applied. For projects built around Reeve RV485 components, this satin zinc bracket provides a specific length option to match shelf depth and loading needs.