Amerock Conrad Satin Nickel Pull For Cabinets

Amerock Conrad satin nickel pull provides a 3-3/4 in (95 mm) center-to-center grip that aligns well with common cabinet drilling patterns, helping streamline layout on new builds or straightforward handle swaps. The pull is part of the Conrad series from Amerock Corporation, so it maintains a consistent style when used across multiple doors and drawers in the same project. Its satin nickel finish offers a muted metallic look that helps reduce visual fingerprints compared to high-gloss surfaces in everyday kitchen or bath use. The pull length of 5-3/16 in creates usable hand clearance beyond the 3-3/4 in hole spacing, which supports a comfortable grasp on drawers or heavier cabinet fronts. With a projection of 1 in off the face, the pull stands out enough for an easy grip while keeping fronts from catching clothing as users move along cabinet runs.

Key Conrad Series Pull Details For Projects

• The 3-3/4 in (95 mm) center-to-center dimension supports consistent drilling across banks of doors and drawers, which helps installers keep alignment straight on longer cabinet runs.
• The 5-3/16 in overall length provides extra grab area at each end, which gives users a solid handhold on wider or heavier drawers without crowding their fingers.
• The 1 in projection sets the pull away from the face enough for comfortable finger clearance, which reduces knuckle contact against the cabinet edge during daily operation.
• The 7/16 in width creates a slimmer front profile, which offers a clean look on modern cabinetry while still presenting a defined edge to pull against.
• The zinc die-cast construction provides a solid, consistent body for the pull, which supports uniform feel across multiple pieces installed throughout a room.
• The satin nickel finish delivers a soft metallic appearance, which pairs well with many hinge finishes and helps keep the hardware visually cohesive in a space.

Installation Geometry And Fit For This Pull

This Amerock Conrad cabinet pull uses a 3-3/4 in (95 mm) center-to-center mounting distance, which ties directly into common 96 mm metric drilling patterns used in many cabinet lines. That spacing makes it practical for both new layout drilling and replacing existing handles with the same center-to-center dimension. The pull projects 1 in from the cabinet face, creating enough offset that fingers can wrap behind the bar while the door or drawer front stays protected from repeated hand contact. At 7/16 in wide, the bar sits with a lean footprint against the surface, allowing it to fit comfortably on narrow rail sections or smaller drawer fronts without visually overwhelming them. The total length of 5-3/16 in spreads the load slightly beyond the mounting holes, which helps distribute pulling force across a broader section of the door or drawer face.

Using The Conrad Pull In Cabinet Layouts

Where This Amerock Conrad Cabinet Pull Fits Best

The Amerock Conrad satin nickel pull, with its 3-3/4 in (95 mm) center-to-center measurement, suits cabinet doors and drawers drilled on that common pattern, supporting consistent layout in kitchens, baths, or shop cabinetry. Its 5-3/16 in overall length gives proportionate coverage on standard-width doors and many drawer fronts, so multiple pulls line up visually across a run without appearing too short or oversized. The 1 in projection makes it practical along walkways where deeper pulls might feel intrusive, while still leaving space for a full finger grip when opening heavier drawers. Because the pull sits only 7/16 in wide, it can work on narrower stile or rail sections without crowding the surrounding profiles or trim details. The satin nickel finish keeps the appearance straightforward and adaptable, helping this pull coordinate with other satin nickel decorative hardware & moldings in the same project.

Why These Dimensions Support Repeatable Results

The 3-3/4 in (95 mm) center-to-center dimension on this Amerock BP29202G10 pull allows installers to use standard jigs or drilling templates designed for that spacing, helping speed layout while maintaining repeatable hole placement. The 96 mm class drilling pattern aligns with many existing cabinet preparations, so when that spacing is already present, swapping to this Conrad series pull does not require shifting or enlarging holes. A 5-3/16 in overall length leaves measurable material beyond each mounting screw location, which helps spread operational forces and supports a balanced look relative to typical face-frame and frameless cabinet door widths. With 1 in of projection, the pull keeps the hand away from the cabinet surface, supporting smoother operation for users with larger hands or when opening tall pantry doors. The zinc die-cast construction provides a uniform molded body, so each pull in a project installs with consistent feel and visual profile from one opening to the next.

Common Questions About Amerock Conrad Satin Nickel Pull

Selecting This Conrad Pull For Your Next Run

The Amerock Conrad satin nickel pull with 3-3/4 in (95 mm) center-to-center spacing, 5-3/16 in overall length, and 1 in projection gives a clear set of dimensions for planning cabinet layouts or replacements. Its zinc die-cast construction and 7/16 in width supply a consistent profile that reads cleanly across multiple fronts. When a project calls for a satin nickel handle in the Amerock Conrad series, this BP29202G10 pull offers a defined size and look that can be repeated across doors and drawers for a unified result.