1 Inch Wire Grommet Cap White For Clean Wire Runs

1 inch wire grommet cap white describes a round plastic part designed for a 1 inch bore hole, so it fits pre-drilled openings sized to that diameter in work surfaces or panels. The product is a one piece plastic round wire grommet from Hardware Concepts, Inc., so the cap and liner work together as a matched set for consistent fit. The liner depth is 1/4 inch, so the grommet seats shallowly in the hole, useful where material thickness or clearance under the surface is limited. The cap has a pivot hinge hole for wire, so the opening manages cables through the surface while allowing them to angle as needed. The product is identified by manufacturer part 6330-010, giving an exact reference when matching this grommet to drawings or reordering for additional installations.

Key Wire Grommet Details That Aid Layout

• The bore hole size is 1 inch, so it aligns with standard drilled openings for small wire pass-through points in desks, counters, or panels.
• The liner depth is 1/4 inch, so it occupies minimal vertical space in the hole, which helps where there is limited room beneath the surface.
• The cap has a pivot hinge hole for wire, so cables can route through while the cap stays seated, supporting a neater finished appearance around the opening.
• The part is a one piece plastic round wire grommet, so the cap and liner function as a single coordinated solution suited to simple cable routing needs.
• The product is from Hardware Concepts, Inc. with manufacturer part 6330-010, so it can be specified and reordered accurately by that exact number.

Wire Grommet Fit And Simple Seating Details

This round wire grommet is specified for a 1 inch bore hole, so installers can drill that size opening and expect the grommet to occupy the cutout consistently. The 1/4 inch liner depth means the grommet does not extend far below the work surface, so it suits panels where deeper hardware would interfere with structures or stored items beneath. As a one piece plastic design, the cap and liner act as a unified insert, so positioning is straightforward once the bore hole is prepared. The pivot hinge hole in the cap guides wire through the opening, so after installation, cables can be passed and oriented while the visible surface remains organized.

Using This Round Wire Grommet In Real Projects

Where This 1 Inch Bore Grommet Works Best

This round wire grommet is part of a grommets product class and is sized for a 1 inch bore hole, so it suits applications where a small, defined opening is needed for routing wires through a surface. The 1/4 inch liner depth supports use in desks, shelves, or panels where material thickness is modest and there is minimal clearance for hardware below. Because the cap has a pivot hinge hole for wire, it is suited to locations where cables enter or exit at slight angles from the opening, such as near the back of a work surface or along a panel edge. The round one piece plastic construction fits with multimedia and workspace components, so it aligns well with installations that organize wiring in offices or similar setups.

Details That Support Repeatable Cutouts And Routing

The specified 1 inch bore hole size gives a clear drilling dimension, so installers can repeat that measurement across multiple panels for uniform appearance and fit. The 1/4 inch liner depth provides a fixed seating height in the opening, so each grommet presents a consistent reveal above and below the surface when the same hole depth is used. The pivot hinge hole built into the cap directs wire through a defined path, so cable movement is guided by the cap rather than the raw edge of the bore, leading to a tidier wire exit point at every location. As a one piece plastic round wire grommet identified by manufacturer part 6330-010, the same part can be referenced in plans and on orders, supporting standardized cutout tooling and repeatable mounting details across projects.

Common Questions About The 6330-010 Wire Grommet

Select This Grommet For 1 Inch Wire Openings

This 1PC 1 wire grommet cap WHT is built for a 1 inch bore hole with a 1/4 inch liner depth, so it serves small cable pass-through points where space is tight. The one piece plastic round design and pivot hinge hole for wire support straightforward routing of cables through desks or panels while maintaining a clean opening sized to this specific Hardware Concepts, Inc. 6330-010 part. Choosing this configuration aligns drilled openings, seating depth, and wire path with a defined, repeatable grommet solution.