Liberty Hardware Citation Pull 3-3/4" (96 mm) Center to Center, Aluminum, PN6504-AL-C

Liberty Citation Series 3-3/4 Inch Pull Use

Liberty Citation Series 3-3/4 inch pull identifies this handle as part of Liberty Hardwares Citation II collection and sets the 3-3/4 inch center-to-center size, so installers can match hole spacing on cabinet doors and drawers already drilled to that layout. The 96 mm center to center measurement restates the same mounting spread in metric, which helps when aligning with European drilling patterns or mixed-spec shop drawings. The aluminum die cast material provides a solid metal pull that remains lightweight, which is useful on standard cabinet fronts where reduced door weight supports smooth hinge performance. The aluminum finish gives the pull a clean, neutral look, allowing it to coordinate with many cabinet colors while keeping visual focus on the overall layout rather than the hardware. Being classified under handles and pulls defines its role as a grasp point for opening and closing doors or drawers in everyday use.

Key Details Of This Liberty Aluminum Pull

• The Citation II collection designation ties this pull to a specific Liberty Hardware design family, which matters when matching or extending an existing run of hardware across multiple cabinet faces for a consistent appearance.
• The aluminum die cast construction creates a molded metal body with uniform dimensions, supporting repeatable drilling and handle alignment across multiple doors during larger cabinet or millwork installations in a shop or on site.
• The aluminum finish provides a single, consistent surface color, which helps installers and fabricators keep a uniform look from one cabinet line to the next when using this pull as a standard selection on a project.
• The 4 inch length gives a defined edge-to-edge size that works comfortably on many cabinet doors and drawers, helping installers judge spacing from door edges and between adjacent pulls for balanced layouts.
• The 3-3/4 inch center to center dimension matches a common drilling standard, which allows straightforward replacement of existing pulls or fast setup of jigs when boring new fronts in production runs.
• The 1 inch projection sets how far the pull stands off the cabinet surface, which provides finger clearance while keeping the handle close to the face for a low-profile look on doors and drawer fronts.

Installation Fit For The 3-3/4 Inch Pull

The 3-3/4 inch center to center specification defines the distance between the mounting holes, which lets installers align this Liberty Hardware pull with existing 3-3/4 inch or 96 mm drilling patterns on cabinet doors and drawers without altering the layout. The 4 inch overall length provides a clear external size, so fabricators can position pulls relative to panel edges and neighboring fronts while maintaining consistent reveals. The 1 inch projection from the cabinet face creates a known standoff, which gives enough space for fingers to grip while maintaining a close-to-door profile that suits many kitchen and bath cabinets. The aluminum die cast build keeps the pull relatively light compared with some solid metals, which can be helpful when outfitting multiple fronts where overall door weight influences hinge and slide performance.

Using This Liberty Hardware Handle In Projects

Where This 96 Mm Center Pull Works Best

This Liberty aluminum cabinet pull sits within the handles and pulls category, positioning it for use on cabinet doors and drawers in woodworking and cabinetry projects supplied by Wurth Baer Supply. The 3-3/4 inch center to center, also listed as 96 mm, ties directly into a standard drilling pattern widely used on kitchen, bath, and built-in cabinets, which is important when installers are updating hardware on existing fronts or setting up line boring equipment. The 4 inch length makes this aluminum die cast cabinet pull comfortable on many common cabinet widths, helping it scale from smaller drawers to full-height doors without overwhelming the face. With a 1 inch projection, the pull provides a defined grip zone while staying tight to the surface, which suits cabinets where a streamlined profile is preferred around adjacent doors, walls, or appliances.

Why These Pull Details Support Repeatable Results

The PN6504-AL-C Liberty pull identifier gives installers and shops a precise part number to specify, which reduces ordering errors when repeating a job, matching prior work, or documenting hardware on project sheets. The Citation II collection reference links this handle to a consistent Liberty Hardware style, so any future additions on the same project can rely on the same profile and finish without reselecting. Having the center to center dimension clearly defined at 3-3/4 inch or 96 mm lets fabricators build or adjust drilling templates one time, then reuse them across multiple fronts to maintain even spacing and speed installation. The 4 inch length and 1 inch projection work together to create a predictable envelope, which helps designers and installers visualize clearances and align multiple pulls in straight, repeatable lines across a run of cabinets.

Common Questions About This Liberty Citation Pull

Selecting This Pull For Cabinet Projects

The Liberty aluminum cabinet pull with 3-3/4 inch, or 96 mm, center to center spacing offers a defined drilling pattern, a 4 inch overall length, and 1 inch projection that fit many cabinet layouts. The aluminum die cast construction and Citation II collection styling provide a consistent hardware choice when specifying cabinets through Wurth Baer Supply. Using the PN6504-AL-C Liberty pull part number, installers and shops can align orders and installations to this specific handle when planning new work or coordinating with existing cabinetry.