Liberty Hardware Citation Pull 5-1/16" (128 mm) Center to Center, Aluminum, PN6505-AL-C

Liberty Citation Series 5-1/16 Pull For Cabinets

Liberty Citation Series 5-1/16 pull identifies this handle as part of Liberty Hardware's Citation II collection, which gives installers a consistent style to match across multiple cabinet and drawer fronts. The aluminum material keeps the pull lightweight while still providing a solid feel during regular use on residential or light commercial cabinetry. An aluminum finish presents a clean, neutral look that coordinates with common hinge and appliance finishes in many shops and kitchens. The 5 inch center to center drilling aligns with a standard handle layout, so existing 5 inch hole patterns on doors or drawers accept this pull without changing the boring pattern. A total length of 5-5/16 inches means the handle slightly overhangs the boring, giving users clear grip points beyond the screw centers for easier operation. The 1-1/16 inch projection spaces fingers off the cabinet face, helping reduce knuckle contact with the door or drawer surface.

Key Liberty Aluminum Pull Details That Matter

• The Citation II collection designation connects this pull to a defined Liberty Hardware family, helping installers maintain visual continuity when outfitting full banks of cabinets or when matching to existing Citation hardware during replacements.
• The aluminum material construction keeps each pull relatively light, which can simplify handling on larger runs of doors and drawers while still delivering a metal feel that suits typical cabinet environments.
• The aluminum finish provides a uniform appearance across the pull, supporting consistent looks on face frames and frameless cabinets where visible hardware alignment is important to the finished job.
• The 5 inch center to center drilling works with standard cabinet boring patterns, allowing straightforward installation on new fronts and direct change-outs on cabinets already drilled at 5 inches.
• The 5-5/16 inch overall length offers grip area beyond the screw locations, giving users a comfortable handhold that spans much of a typical drawer front width for everyday opening and closing.
• The 1-1/16 inch projection sets the pull away from the cabinet surface enough to accommodate a full finger grip, supporting smoother door and drawer operation without crowding the front.

Installation And Fit Details For This Cabinet Pull

The 5 inch center to center measurement defines the exact drilling distance between mounting points, so door and drawer fronts bored on a 5 inch pattern line up with this pull during installation. This helps streamline layout on new cabinet runs that follow standard metric or imperial drilling jigs around the 128 mm span. The 5-5/16 inch overall length gives a clear sense of how much of the front the handle covers, which matters when laying out hardware relative to panel edges or rail widths. A 1/2 inch width keeps the pull visually slim on narrow drawer fronts while still providing a defined edge for grip. The 1-1/16 inch projection determines how far the pull stands off the surface, guiding clearances near adjacent doors, walls, or tall cabinet frames.

Using The Liberty Citation II Pull On Projects

Where This 5 Inch Center Pull Fits Best

The 5 inch center to center drilling positions this pull well on medium to larger cabinet doors and drawer fronts that already use, or are planned for, a 5 inch layout. In shops working from drilling jigs set to 128 mm spacing, the matching 5 inch specification keeps the pull aligned with common boring setups while still fitting standard imperial measurements. The overall 5-5/16 inch length means the pull spans enough of a drawer face to look balanced on base cabinets, vanities, and many kitchen wall cabinets. With a 1/2 inch width, the pull remains proportional on narrower faces, so installers can run the same model across uppers and lowers without visual imbalance. The aluminum material and finish suit interiors where a neutral metal tone supports a range of door colors and laminate surfaces.

Details That Support Consistent Cabinet Hardware Layout

The Citation II collection label allows hardware planners to specify a single Liberty Hardware family across a project, simplifying selection when matching pulls across multiple room zones or future additions. The 5 inch center to center dimension standardizes drilling, which reduces layout variability and supports repeated use of the same templates or boring equipment. That repeatable spacing makes it easier to keep hardware rows straight across long runs of drawers. The 1-1/16 inch projection also plays into layout decisions, since it defines stand-off from the front and helps anticipate clearances near tall cabinet sides or adjacent appliances. The 1/2 inch width ensures that the pull line stays visually light, which can be useful when aligning several pulls closely on stacked drawers where bulkier handles might crowd the design. The aluminum finish keeps the color tone consistent from piece to piece, supporting even sightlines across cabinet banks.

Common Questions About The Liberty Citation Aluminum Pull

Select This 5 Inch Liberty Pull For Matching Runs

The Liberty Citation Series 5-1/16 pull combines a 5 inch center to center layout with a 5-5/16 inch overall length, giving installers a clear fit for standard cabinet drilling patterns. The aluminum material and aluminum finish create a neutral, consistent metal appearance that coordinates across many cabinet styles. With a 1/2 inch width and 1-1/16 inch projection, this pull offers practical hand clearance while keeping sightlines clean on doors and drawers. For projects where a defined collection, known as Citation II, and repeatable 5 inch drilling are priorities, this Liberty Hardware handle provides a straightforward choice.