Domi Snap-On 2-Cam Adjustable Straight Mounting Plate, Nickel-Plated, Dowelled, 3mm

Domi Snap-On Mounting Plate For Precise Hinge Setup

Domi snap-on 2-cam adjustable straight mounting plate gives a hinge base that uses dual eccentric cams for both height and depth, so cabinet doors can be aligned accurately on the case side. The plate is part of the Salice "Domi" slim style hinge mounting plate family, so it supports slim-line installations where hinge hardware sits close to the cabinet wall. The 3mm plate height sets the starting overlay geometry, which matters when repeating the same door reveal across a run of cabinets. Nickel-plated, corrosion-resistant construction keeps the die-cast steel body protected in typical cabinet environments, supporting long-term alignment stability. The cabinet side attachment method uses a 10 mm knock-in dowel, giving a positive mechanical connection into the side panel without separate lead-in cutting on the plate itself.

Key Mounting Plate Details That Save Time

• The Salice "Domi" slim style hinge mounting plate layout supports compact hardware spacing, which helps when fitting hardware inside tight cabinet interiors or near dividers.
• Die-cast steel construction provides a solid base for the hinge arm, which helps keep cam adjustments consistent after repeated door cycling in normal cabinet use.
• Height adjustment by eccentric cam plus or minus 2 mm lets the installer fine-tune vertical door position on the cabinet, reducing door misalignment along stacks of wall or base units.
• Depth adjustment by eccentric cam from 0.5 mm to plus 2.8 mm lets the door move closer or farther from the cabinet front, which helps achieve the correct reveal and close without re-drilling.
• Nickel-plated, corrosion-resistant finish protects the plate surface in typical kitchen or bath moisture conditions, which helps preserve smooth cam function over time.
• The cabinet side attachment method using 10 mm knock-in dowel engages pre-drilled holes, which speeds installation on line-bored cases and provides repeatable plate positioning.

Mounting Plate Installation And Adjustment Workflow

The dowelled mounting plate attaches on the cabinet side using a 10 mm knock-in dowel, so the plate locates directly in prepared holes before the hinge arm is added. Height adjustment by eccentric cam plus or minus 2 mm lets the installer dial the vertical door position after the plate is fixed, which avoids moving screw positions in the cabinet. Depth adjustment from 0.5 mm to plus 2.8 mm by eccentric cam gives front-to-back tuning at the plate, so the hinge arm can be snapped on while final reveal is still adjustable. The snap-on hinge connection supported by this plate helps when hanging multiple doors, because each plate can be set to the same cam positions to repeat results.

Using The Salice Domi Plate In Cabinet Runs

Where This 3mm Salice Mounting Plate Fits

This hinge mounting plate is designed for cabinet side attachment using a 10 mm knock-in dowel, so it suits casework with matching 10 mm dowel bores on the interior walls. The straight 3mm plate height establishes a predictable offset between hinge arm and cabinet side, which is important when designing overlay and reveal on frameless cabinets. As part of the Salice "Domi" slim style hinge mounting plate line, it is built for use with compatible Salice hinge arms that connect using a snap-on interface, allowing the door hardware to remain close to the cabinet side. The die-cast steel body supports these connections without flexing under normal door loads, so hinge action remains centered on the intended pivot geometry across the width of the door.

How Dual Cams And Nickel Finish Support Accuracy

The two eccentric cams on this mounting plate give separate height and depth adjustment ranges, so installers can correct for drilling tolerances or case racking without altering primary bore locations. Height adjustment plus or minus 2 mm on the plate lets vertical reveals be tuned relative to neighboring doors and cabinet tops, which is useful when walls or floors are out of level. Depth adjustability from 0.5 mm to plus 2.8 mm at the plate lets the door face sit flush or slightly proud according to the design, helping maintain consistent appearance along entire cabinet runs. The nickel-plated, corrosion-resistant finish on the die-cast steel helps the cams turn smoothly even in humid rooms, supporting repeatable fine adjustments during initial setup and later service. Lifetime warranty coverage on the plate reflects its role as a long-term hinge base in everyday cabinet use.

Common Questions About This Salice Mounting Plate

Selecting This Plate For Your Hinge Layout

The Domi snap-on 2-cam adjustable straight mounting plate, with 3mm height and 10 mm knock-in dowel attachment, suits cabinet builds that need repeatable hinge geometry and on-plate fine tuning. Dual eccentric cams for height and depth let you align doors after the case is assembled, while the nickel-plated, corrosion-resistant die-cast steel body and lifetime warranty support long-term service. When a project calls for a Salice "Domi" slim style hinge mounting plate that delivers precise door positioning on the cabinet side, this BAP7R39 plate is a practical choice.