Berenson Advantage Plus Six Series 5-1/16" (128 mm) Center to Center Polished Chrome Pull, - 9407-4026-P

Berenson Advantage Plus 6 Pull For Cabinets

Berenson Advantage Plus 6 pull gives you a 5-1/16 inch (128 mm) center to center handle that lines up with common drilling patterns, which helps when you are matching existing holes on cabinet doors and drawers. The pull has an overall length of 5-1/2 inches, so it spans slightly beyond the hole spacing, giving you comfortable grip area at each end. Its 1 inch projection sets the hand clearance off the front of the cabinet, which supports finger space without bringing the handle too far into the work area. The 13/16 inch width provides a substantial feel on the door or drawer face, which matters when multiple hardware pieces must look consistent across a run. Aluminum material keeps the pull light, and the polished chrome finish provides a bright, reflective look that coordinates with other chrome decorative hardware in the same space.

Key Advantage Plus 6 Pull Details In Use

• The 5-1/16 inch (128 mm) center to center dimension matches many cabinet drilling setups, which simplifies layout when installing on standard door and drawer fronts.
• The 5-1/2 inch overall length gives extra handle surface beyond the mounting points, which supports a secure grip for opening wider or heavier cabinet fronts.
• The 1 inch projection holds the pull off the surface, which provides finger clearance while keeping the profile tight to the cabinet face for a clean line.
• The 13/16 inch width creates a visible bar on the front, which helps the hardware read correctly in proportion to typical residential and light commercial cabinet panels.
• The aluminum construction keeps the pull lightweight, which is useful when repeating this Berenson handle across many doors and drawers on a larger installation.
• The polished chrome finish matches other polished chrome decorative hardware and moldings, which supports a consistent finish schedule throughout the project.

Mounting And Fit Details For Cabinet Layouts

This Advantage Plus 6 cabinet pull is built with a 5-1/16 inch (128 mm) center to center measurement, so the mounting points are spaced for standard handle drilling on many cabinets. The base dimensions are 3/8 inch, which defines the footprint where each end meets the door or drawer surface and influences where the pull visually sits on narrow rails or stiles. With a projection of 1 inch and width of 13/16 inch, the pull occupies a compact envelope off the face, which helps keep door swing paths and drawer clearances predictable in tight layouts.

Where This 5-1/16 Inch Pull Works Best

Using The 128 mm Center To Center Layout

The 128 mm (5-1/16 inch) center to center drilling of this Berenson Advantage Plus 6 pull aligns well with many modern cabinet programs that use metric spacing, which is useful during replacements or new installations using a standard jig. The 5-1/2 inch overall length positions the ends of the pull slightly past the mounting holes, which visually balances the hardware on typical drawer fronts and framed or frameless cabinet doors. With 3/8 inch base dimensions at each contact point, the pull seats on narrow rails without overwhelming them, while still covering the drilled hole area. The 1 inch projection and 13/16 inch width define a compact working profile, which allows doors to open near adjacent panels without the handle dominating the reveal lines. Aluminum construction keeps each pull light on the door edge, which can be helpful when installing multiple pulls on tall pantry doors or large drawer banks where overall hardware weight adds up.

Why Finish And Dimensions Support Consistency

The polished chrome finish on this Advantage Plus 6 aluminum pull delivers a bright, uniform surface, which helps decorative hardware match across hinges, knobs, and other polished chrome components in the same project. Because the center to center is fixed at 5-1/16 inches, drill patterns remain consistent from door to door, which supports repeatable layout on production runs or multi-cabinet installations. The 13/16 inch width and 5-1/2 inch length work together to create a handle that reads as a mid-size pull, which can be used on both doors and drawers without changing visual scale. A 1 inch projection establishes predictable hand clearance, so the same feel is maintained anywhere this pull is installed on a bank of cabinets. The 3/8 inch base footprint ties these dimensions together at each end, which helps the pull sit solidly on the surface while presenting a consistent margin around the mounting area.

Common Questions About The Advantage Plus 6 Pull

Selecting This Pull For Your Cabinet Project

The Berenson Advantage Plus 6 pull pairs a 5-1/16 inch (128 mm) center to center layout with a 5-1/2 inch length, creating a mid-size handle that suits both doors and drawers in one program. Its 1 inch projection, 13/16 inch width, and 3/8 inch base dimensions define a compact profile that fits many cabinet styles. With aluminum construction and a polished chrome finish, this pull aligns with projects that call for lightweight hardware and a bright chrome look. For cabinet installations needing a consistent 128 mm handle, this Advantage Plus 6 model provides a defined set of dimensions to plan around.