Tiomos Adjustment Wing Mounting Plate For Precise Hinges

Tiomos adjustment wing mounting plate from Grass America is a hinge mounting plate designed for Tiomos applications, giving installers a defined interface between cabinet and hinge. The 0mm wing mounting plate provides a zero-offset base, which helps align doors when the cabinet construction or hinge geometry calls for a flush reference plane. The plate is made of steel, so it offers a solid seating surface for the hinge over time. Its nickel-plated finish creates a smooth metal surface, which supports consistent operation where the hinge meets the plate. This hinge mounting plate is part of the Grass America Tiomos system, so it serves as the fixed partner for the adjustable hinge arm in typical cabinet builds.

Key Mounting Plate Details For Daily Work

• The 0mm mounting plate height sets the hinge arm at a neutral level, which supports standard door overlays when the case and hinge are laid out for a zero-rise base.
• The wing-style mounting plate footprint spreads contact over a wider area, which helps the hinge load transfer into the cabinet side on typical furniture or casework.
• The 3 point fixing design locates the plate with three fastener positions, which stabilizes the hinge interface under repeated door cycles.
• Height adjustment via elongated screw holes allows the plate position to shift within the slot travel, which lets installers fine-tune door position after the carcase is assembled.
• The screw-on configuration uses mechanical fixing, which lets the plate be mounted, loosened, or repositioned directly on the cabinet panel during fitting.
• Pre-mounted Euro screws are integrated into the plate at the factory, which speeds installation in Euro-drilled cabinets because the fasteners are already aligned with the plate.
• The nickel-plated surface on the steel plate gives a consistent metal-to-metal contact area, which supports smooth hinge movement at the connection point.

Screw-On Tiomos Plate Setup And Adjustment

This screw-on Tiomos hinge mounting plate is designed to fasten directly to the cabinet using its 3 point fixing layout, so the installer works from a stable base when attaching the hinge arm. The 0mm plate height means the hinge arm sits at cabinet panel level, which simplifies layout where the drilling pattern is based on a flush reference surface. Height adjustment via elongated screw holes gives vertical flexibility at the plate, so small door reveal corrections can be handled without re-drilling the cabinet. Because the Euro screws are pre-mounted in the plate, the plate and fasteners behave as one unit during assembly, which makes handling quicker when moving between cabinets on a larger run.

Using This Grass America Plate In Cabinet Runs

Where This Tiomos Wing Mounting Plate Fits

This Grass America hinge mounting plate is specified as a Tiomos adjustment wing mounting plate, so it is intended to work as the mounting base in Tiomos hinge layouts. The 0mm designation defines the plate height at the cabinet interface, which matters when the drilling pattern and door overlay are calculated around a zero-height base plate. The wing configuration of the plate is suited to cabinet sides or similar flat mounting areas, giving a broad contact profile for the hinge connection. With 3 point fixing, the plate suits applications where the door will be operated frequently and hinge stability at the cabinet side is important over the life of the cabinet. The pre-mounted Euro screws support use in construction that follows Euro-style drilling for mounting points.

How Plate Details Support Repeatable Adjustment

The height adjustment via elongated screw holes on this Tiomos hinge base plate provides a controlled slot path, which lets installers shift the plate position during fitting to dial in door reveals across a run of cabinets. Because the fixing pattern uses three points, the plate resists rotation while screws are tightened, which helps maintain the adjusted position once the door alignment is set. The 0mm plate height works with hinge arms designed for that reference level, so repeated installations can follow the same drilling and layout without recalculating base height. Nickel-plated steel construction gives a consistent metal interface between hinge arm and plate, which supports repeatable clamping and release when doors are removed and re-installed for finishing or access. With pre-mounted Euro screws and screw-on fixing, the installer can move from cabinet to cabinet using the same sequence, which streamlines production work and helps keep door alignment consistent across the project.

Common Questions About This Tiomos Mounting Plate

Selecting This Plate For Tiomos Hinge Projects

The Tiomos adjustment wing mounting plate with pre-mounted Euro screws and 3 point fixing offers a defined 0mm base height, steel construction, and nickel-plated finish for hinge work. When a project calls for a Grass America Tiomos hinge mounting plate built around screw-on fixing and height adjustment via elongated screw holes, this wing-style base plate provides the cabinet-side interface required for that layout. Choose it when the drilling pattern, overlay, and workflow are set up around a 0mm Tiomos hinge base plate with integrated Euro screws.