Tiomos Wing Steel Base Plate With Pre-Mounted Euro Screws (13.5mm) 2mm Height

Tiomos Wing Steel Base Plate For Precise Mounting

Tiomos wing steel base plate defines this Grass America hinge mounting plate as a dedicated mounting point for Tiomos hinges, so you get a known interface when laying out and hanging doors in cabinet runs. The 2mm height establishes a fixed reference between the hinge arm and the cabinet side, which supports consistent reveals from cabinet to cabinet. The steel construction provides a solid bearing surface for the hinge connection, helping the hinge transfer door loads back into the casework. The wing style plate spreads that load over a wider footprint on the cabinet side, which is useful when working in particleboard or similar substrates. The pre-mounted Euro screws match Euro-style system construction, so the plate ties directly into system holes without separate fastener selection. The stated 13.5mm reference links this plate to Tiomos geometry, helping keep your drilling pattern and hinge arm choice aligned on a job.

Key Mounting Details That Support Your Work

• The 2mm height of this Grass America hinge mounting plate sets a defined base level between cabinet and hinge arm, which simplifies repeating the same door overlay across multiple openings in a kitchen or commercial run.
• The wing style design spreads bearing area on the cabinet side, which helps distribute hinge forces when doors are cycled repeatedly in everyday cabinet use.
• The 3 point fixing noted in the description secures the plate at three locations, which helps resist twisting of the hinge mount and supports long-term alignment of the door edge to adjacent fronts.
• The steel material creates a rigid platform for the Tiomos hinge connection, which supports crisp door action when opening and closing and helps the mounting points stay stable in normal service.
• The pre-mounted Euro screws tie directly into Euro system holes, which streamlines installation on line-bored casework and supports consistent positioning without separate fastener setup.

Mounting And Height Adjustment For Tiomos Hinges

This Grass America Tiomos wing steel base plate provides 3 point fixing, so the plate anchors firmly to the cabinet substrate as the hinge is attached and adjusted. Height adjustment via elongated screw holes gives vertical play at the plate, allowing the hinge position to be shifted up or down relative to the cabinet side. That adjustment range helps fine-tune door reveal after the casework and fronts are already in place. The 2mm plate height works with Tiomos hinge geometry to hold the arm at a known distance from the cabinet, which supports predictable overlay results when using consistent drilling patterns. The 13.5mm reference in the product name ties this plate into Tiomos system measurements, helping keep hinge arm choice, boring pattern, and plate selection coordinated on a project.

Using This Tiomos Hinge Base Plate On Jobs

Where This 2mm Wing Plate Fits Best

This Tiomos wing steel base plate from Grass America is specified as a hinge mounting plate for Tiomos hinges, so it fits naturally into Euro-style cabinet construction where system holes and hinge layouts are already defined. The 2mm height positions the Tiomos hinge arm at a specific stand-off from the cabinet side, supporting consistent overlay when the same drilling pattern is repeated across a bank of cabinets. With 3 point fixing, the plate locks to the cabinet side at three locations, which is useful on taller doors where hinge loads can introduce twisting forces at the mount. The wing configuration increases the footprint on the cabinet side, which supports that 3 point layout and helps the hinge forces be shared across more material in the cabinet side panel.

Why Adjustment And Euro Screws Support Workflow

The height adjustment via elongated screw holes lets this Tiomos wing steel base plate handle small variances in drilling or cabinet construction by allowing vertical movement at the plate before final tightening. That adjustability is helpful during installation when doors need slight shifts to align with adjacent fronts, end panels, or appliance reveals. The pre-mounted Euro screws connect directly into Euro-style system holes, so the installer can position the plate and fasten it using the same system layout already used for shelves and other hardware, which keeps the workflow consistent on line-bored cabinets. As a Grass America hinge mounting plate with the Tiomos designation, it ties directly into the Tiomos hinge family geometry, so the hinge arm, base plate height, and boring pattern work together toward repeatable door fit across the project.

Common Questions About This Tiomos Mounting Plate

Select This Plate For Tiomos System Consistency

The Grass America Tiomos wing steel base plate with 2mm height, 3 point fixing, height adjustment via elongated screw holes, and pre-mounted Euro screws provides a defined mounting solution within the Tiomos hinge system. When a project calls for Tiomos hinges on Euro-style casework, this hinge mounting plate ties hinge geometry, system holes, and door reveals together into a coordinated setup. Order this plate from Wurth Baer Supply to align your Tiomos hinge choice with a matching base plate that supports repeatable cabinet construction and door alignment.