Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
This Salice Series 200 blind corner hinge is built for inset doors on face-frame and frameless cabinets that sit adjacent to a wall or an abutting cabinet run, where a standard hinge arm would cause the door to strike the neighboring surface. Its 94-degree opening is the engineered geometry that lets the door clear the cabinet front cleanly in that constrained position, and it mounts to the door with inline dowels for a CNC-ready, screw-free cup installation.
A blind corner cabinet sits at the end of a run where one side is walled in or butted against another cabinet, leaving no room for the door to swing freely. When that door is also an inset door, the challenge doubles: the door must clear the cabinet opening flush while its swing is limited by the adjacent obstruction. The 94-degree opening on this hinge is the correct engineering response. It restricts the swing precisely enough to keep the door from colliding with the neighboring surface, without cutting access any further than the situation demands. The reduced angle is the feature, not a compromise.
The 35mm cup bores into the back of the door at the standard depth. The inline dowel design means the cup locks into pre-bored dowel holes in the door panel, so no cup screws are needed. That makes it a natural fit for production shops running CNC. The arm then connects to a Salice base plate mounted to the cabinet. The plate is sold separately and must be a Salice plate matched to this series; plates from other brands will not connect to this hinge.
The hinge is steel in a nickel finish. On an inset door, where the hinge body is mostly hidden by the door sitting inside the opening, the finish matters most at the visible cup edge. Nickel keeps that detail consistent with other nickel hardware in the run. The self-close spring is built into the hinge rather than added on, so there is nothing extra to install or adjust. Height adjustment of plus or minus 2mm and side adjustment of plus 4.5 and minus 1.5mm give you enough range to bring the inset door back to an even reveal if the cabinet shifts after installation.
Production cabinet shops running CNC equipment benefit most directly from the dowel mount, which eliminates the cup-screw step and feeds into a standard pre-boring pattern. Custom builders and installers working tight end-of-run positions where inset doors meet a wall or an adjacent cabinet will recognize this as the hinge that solves that specific layout problem. It suits both face-frame and frameless construction, so it works across a mixed job. Because it is a self-close hinge and not a soft-close hinge, the spring pulls the door shut rather than cushioning it; for a damped, quiet close, the Silentia+ soft-close version of this series is the better call.
The 94-degree opening is intentional for blind corner applications. A standard 110-degree swing would drive the door into the adjacent wall or cabinet in a corner position. The reduced angle is the geometry that lets the door clear its neighbor without binding.
Inset means the door sits inside the cabinet opening, flush with the frame or panel edge, with a small even gap on all sides. An overlay door covers the outside of the opening. This hinge is for inset doors only; using it for an overlay application will misplace the door position.
Yes. The hinge arm connects to a Salice base plate that mounts to the cabinet, and the plate is sold separately. Use a Salice plate matched to your cabinet type and the door position. Plates from other brands will not fit this hinge.
No. Self-close means a spring pulls the door shut once it is released within the last few degrees of travel. Soft-close adds a damper that slows the door so it does not slam. This hinge has self-close only. For a cushioned, quiet close, choose the Silentia+ soft-close version of this series.
When an inset door meets a blind corner on either a face-frame or frameless cabinet, this Salice Series 200 hinge provides the correct swing geometry, a production-friendly dowel mount, and the adjustment range to hold a clean reveal over time.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 3000 Each |  UBS2XX85H9 Mfr# S2XX85H9 | Flange Cover Cap, Nickel | ||||
Sold in: 1 Each |  UBS2A637XF Mfr# S2A637XF | Salice 94° Hinge Stop Device for Series 200 Hinges S2A637XF |