Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Dynapro 2D left-hand front locking device from Grass America anchors the drawer front to Dynapro slides while providing 2D or 3D adjustment, so you can fine-tune the front alignment after installation instead of fighting fixed positions. This locking device is built for standard width or inset drawers, giving flexibility across common cabinet layouts where you want one hardware standard. The minimum inside drawer width of 5-7/8 inches (150 mm) defines how narrow the drawer box can be, helping plan small drawers without running into clearance issues. Lightweight, high strength material keeps moving masses low at the slide front, which helps drawers run smoothly while still holding adjustment under load. As a left-hand part, this device pairs with the matching right-hand version, so each drawer front is supported consistently on both sides.
This Dynapro left-hand front locking device is intended to mount at the front of the drawer with Dynapro slides, so adjustment happens where the reveal is most visible. Pre-drilling is recommended with a 3/32 inch (2.5 mm) bit, which gives a pilot sized to grip typical fastening screws while reducing the risk of splitting drawer material around the lock area. Using the specified pilot size also helps position the device consistently from drawer to drawer, so the full height adjustment range of plus 3.5 mm and side adjustment range of plus or minus 1.5 mm remain usable across a run. On versions with 3D capability, the plus 3.0 mm forward depth adjustment lets you nudge the drawer front relative to the cabinet, bringing it flush with adjacent fronts after the slides are fixed.
This Dynapro 2D left-hand front locking device with flange fits drawer applications using Grass Dynapro slides where front alignment control matters, such as kitchen and bath cabinets or casework with visible inset gaps. Its suitability for standard width or inset drawers means the same hardware supports both overlay and inset design choices, which streamlines hardware planning on mixed installations. A minimum inside drawer width of 5-7/8 inches (150 mm) defines where it can be used in narrow boxes, helping maintain clearance around sink bases or partitioned drawers. Lightweight, high strength material keeps the clip rigid at the front while avoiding excess mass on the slide members, which helps preserve smooth slide operation and reduces stress at the connection point over repeated use.
The height adjustment range of plus 3.5 mm allows you to raise the drawer front relative to the box, so you can step up fronts along a tall cabinet or match existing lines even if the box is slightly out of square. Side adjustment of plus or minus 1.5 mm lets you correct for small racking or carcass variation by shifting the front left or right at the clip instead of reworking the drawer sides. On Dynapro installations using the 3D version, the plus 3.0 mm forward depth adjustment adds front-to-back control, so you can bring fronts even with neighboring doors or panels after the runners are fixed. Because this is a left-hand locking device, pairing it with the corresponding right-hand part gives mirrored adjustment on both sides, which helps maintain parallel sight lines and consistent gaps from top to bottom on multi-drawer stacks.
This Dynapro 2D left-hand front locking device is for drawers running on Grass Dynapro slides, and it supports both standard width and inset drawer applications where front alignment is important.
This Dynapro locking device provides 2D or 3D adjustment, so you can correct height, side, and, on 3D versions, depth positions, helping align drawer fronts cleanly after the slides and boxes are installed.
The Dynapro front locking device has a height adjustment range of plus 3.5 mm, which lets you fine-tune vertical reveal lines between drawers or between drawers and doors along a cabinet run.
This Dynapro left-hand device offers side adjustment of plus or minus 1.5 mm, allowing small left-right corrections at the front so reveals track straight against cabinet sides or face frames.
On the 3D version, the plus 3.0 mm forward depth adjustment lets you move the drawer front outward, helping flush it with adjacent fronts after the slides are mounted in the cabinet.
A 3/32 inch (2.5 mm) pilot suits typical fasteners for the Dynapro locking device, supporting a secure hold in the drawer front material while helping control split risk around the mounting points.
The Grass America Dynapro 2D left-hand front locking device with flange ties the drawer front to the slide while building in 2D or 3D adjustment, so you can dial in gaps without rebuilding drawer boxes. Its defined minimum inside drawer width of 5-7/8 inches (150 mm) and specified height, side, and, on 3D versions, forward depth ranges give clear parameters for layout and tuning. For projects using Dynapro slides where clean, consistent reveals matter, this left-hand device provides a predictable way to align fronts across standard width or inset drawers.
Sold In: 1 Each
