
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Dynapro 3D right front locking device gives Grass America Dynapro drawers 2D or 3D adjustment, so you can fine-tune drawer position after installation. This right front locking device is designed for standard width or inset drawers, supporting common cabinet layouts in the shop or on site.
The minimum inside drawer width of 5-7/8 inches, or 150 mm, defines the smallest drawer interior this part is intended to support, which helps when planning narrow drawer banks or specialty pull-outs. Lightweight, high strength material keeps the component easy to handle during assembly while maintaining structural performance when drawers are adjusted.
The 3D version provides height, side, and forward depth adjustment, so installers can bring drawer fronts into alignment along multiple axes. The right-hand orientation identifies this component as the locking device for the right side of the drawer, which matters when matching it with the correct left-hand part and Dynapro slide set.
Dynapro 3D drawer adjustment clip is specified with depth adjustment range of plus 3.0 mm forward adjustment on the 3D version, so the drawer front can be brought closer to the cabinet face when needed. This helps when gaps at the front look slightly proud and require fine forward movement.
Pre-drilling recommended 3/32 inch, or 2.5 mm, guides drill bit selection for the mounting holes, which supports cleaner installations in typical drawer box materials. The right front locking device configuration simplifies orientation, because it is dedicated to the right side location on the drawer and works with Dynapro hardware designed for front locking clips.
The Grass America branding and Dynapro naming tie this part directly to the Dynapro slide family, which helps match this front clip to projects already built or specified around that system. The combination of height, side, and depth adjustment ranges lets installers dial in drawer fronts to match surrounding doors and drawers with controlled, repeatable movements.
Grass Dynapro 3D front clip is used on drawers that require 2D or 3D adjustment, so it suits cabinetry where front alignment is a visible detail. The right front locking device location puts this part at the leading edge of the drawer box on the right-hand side, forming part of the connection between the Dynapro runner and the drawer.
For standard width or inset drawers, this component supports installations where the drawer front either overlays the cabinet or sits inset within the opening. The minimum inside drawer width of 5-7/8 inches, or 150 mm, defines drawers that fall within the intended operating envelope, which fits many utility, kitchen, bath, and shop drawers built around Dynapro hardware.
Because the material is described as lightweight, high strength, installers can handle and position the clip easily, while still relying on it to hold adjustment settings during repeated drawer use in typical woodworking environments.
Dynapro 3D drawer adjustment clip offers height adjustment range of plus 3.5 mm, which lets installers raise the drawer front to line up top edges across multiple drawers when the cabinet or face frame has slight variations. The side adjustment range of plus or minus 1.5 mm lets the drawer front shift left or right in small increments, which is useful for centering fronts within their openings and balancing gaps against adjacent fronts.
The depth adjustment range of plus 3.0 mm forward adjustment, specified for the 3D version, gives forward movement to close up the space between the drawer front and the cabinet face, so reveals can be tightened when they appear too deep. Together, these 2D or 3D adjustments turn the Dynapro 3D right front locking device into a fine-tuning point that supports clean, repeatable alignment across entire drawer runs.
Pre-drilling recommended 3/32 inch, or 2.5 mm, provides a clear drilling dimension that supports consistent screw-hole sizing wherever this clip is mounted in a drawer production run. The manufacturer part number F134108948233 uniquely identifies this specific right 3D front clip with no flange, which matters when re-ordering or matching it with existing Dynapro-equipped drawers.
The Dynapro 3D right front locking device is specified for standard width or inset drawers, so it is suited to drawer fronts that either overlay the cabinet or sit inset within the opening.
The Dynapro 3D front clip offers 2D or 3D adjustment ranges that let installers fine-tune height, side, and forward depth positions, supporting precise drawer front alignment after the drawer box is mounted.
The Dynapro 3D right front locking device is intended for drawers with a minimum inside drawer width of 5-7/8 inches, or 150 mm, guiding layout decisions for narrower drawers.
The Dynapro 3D drawer adjustment clip offers height adjustment range of plus 3.5 mm and side adjustment range of plus or minus 1.5 mm, which supports controlled vertical and lateral tuning of drawer fronts.
The Dynapro 3D right front locking device offers depth adjustment range of plus 3.0 mm forward adjustment, allowing the drawer front to move closer to the cabinet face for tighter reveals.
The Dynapro front clip lists pre-drilling recommended 3/32 inch, or 2.5 mm, which guides bit choice so mounting holes match the intended fastener sizing in typical drawer materials.
Grass America Dynapro locking device with 2D or 3D adjustment, right front orientation, and specified adjustment ranges gives installers controlled alignment for standard width or inset drawers. By working within the minimum inside drawer width of 5-7/8 inches, or 150 mm, and using the documented height, side, and depth adjustment capabilities, this Dynapro 3D right front locking device F134108948233 supports building and tuning drawers around the Dynapro slide system with predictable, repeatable results.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each | GFF134108947233 Mfr# F134108947233 | Dynapro 3D Left Front Locking Device No Flange |