Hickory Hardware Eclipse 3" (76 mm) Center to Center Vintage Bronze Pull, P14114-VB

Hickory Hardware Eclipse Pull For Cabinets

Hickory Hardware Eclipse pull gives you a 3 inch center to center handle that lines up with standard drilled cabinet holes, so you can swap or install pulls without changing your boring pattern on doors or drawers. Branded under Belwith Keeler with manufacturer part P14114-VB, it ties directly to the Eclipse collection, helping match this pull with other Eclipse pieces in the same project layout. The pull uses zinc material, which creates a solid-feeling grip while keeping the piece manageable for everyday cabinet and drawer use. A vintage bronze finish runs across the pull, lending a darker metallic tone that works well when coordinating with similarly toned hinges or other decorative hardware. Overall length of 3-7/8 inch gives you a little overhang past the screw centers, which helps cover previous screw marks around existing holes on replacement jobs.

Key Eclipse Pull Details For Cabinet Work

• The 3 inch center to center layout creates a straightforward fit on cabinets drilled for common 3 inch pulls, keeping layout consistent across doors and drawers during new installs or upgrades.
• The 3-7/8 inch length gives visual coverage beyond the mounting points, which helps mask slight scuffs or wear near existing holes when you replace older handles.
• The 3/4 inch projection sets the pull off the face of the cabinet, giving fingers room behind the handle while keeping the profile tight for doors that swing past nearby obstacles.
• The 3/8 inch width provides a slim front view, so the pull looks clean on narrow drawer fronts or tight rail spaces while still offering enough edge for a solid grip.
• The vintage bronze finish adds a darker, warm tone that coordinates with similar decorative hardware finishes, helping create a consistent look across a run of cabinetry.

Cabinet Pull Fit, Drill Spacing, And Handling

This 3 inch center to center pull is sized to match a very common drilling pattern, so it works neatly where cabinets or drawers are already bored on 3 inch spacing. With an overall 3-7/8 inch length, the pull extends slightly past the mounting points, which is useful when aligning on face frames or overlay doors that benefit from a little extra coverage around the screw area. A 3/4 inch projection means the grip stands off the surface just enough for fingers, which helps on frequently used doors without pushing the pull out too far into walkways or tight galley runs. At 3/8 inch width, the Eclipse pull sits visually light on the front while still giving a defined edge to grab, which is helpful on smaller drawer fronts where a bulky handle would dominate the face.

Using The Hickory Hardware Eclipse Pull In Projects

Eclipse Collection Pull In Cabinet Runs

The Hickory Hardware Eclipse pull from the Eclipse collection is intended for cabinet and drawer use, so it fits naturally on kitchen, bath, or shop casework that needs a consistent handle line. With the 3 inch center to center dimension, it works along banks of drawers and doors that share the same drilling, supporting straight alignment down a cabinet run. The 3-7/8 inch overall length gives each handle a balanced proportion on typical residential cabinet door widths or standard drawer faces, so the pulls do not look undersized on most fronts. A 3/4 inch projection off the surface allows the hand to catch the pull quickly when opening heavier drawers, which is useful in work areas where repeated access is common. The 3/8 inch width keeps the pull from crowding narrow stiles, so it can be used on smaller doors in upper cabinets while still matching lower cabinet hardware in the same space.

Details That Support Replacement And Visual Consistency

The P14114-VB pull, with its 3 inch center to center spacing, is well-suited to replacement jobs where existing cabinets already use this common pattern, because it lines up with the current holes and maintains original spacing. The vintage bronze finish gives a uniform dark metallic appearance across each pull, which helps tie together mixed cabinet zones when you repeat the same pull style throughout a room. Zinc material construction provides a sturdy base for the pull, which supports repeated daily use on frequently opened drawers and doors. The Eclipse collection identity makes it easier to specify this exact style when coordinating multiple hardware positions in the same project, so matching handles maintain the same profile and finish. With brand identification as Belwith Keeler, the part number P14114-VB can be referenced across ordering and planning notes to keep reorders aligned to the same pull.

Common Questions About This Eclipse Cabinet Pull

Selecting This Vintage Bronze Pull For Your Job

The Hickory Hardware Eclipse pull with 3 inch center to center spacing, 3-7/8 inch overall length, and 3/4 inch projection gives you a defined set of dimensions to work into cabinet layouts. Zinc construction paired with a vintage bronze finish delivers a consistent look and feel across doors and drawers that use this model. With clear identification as Belwith Keeler part P14114-VB from the Eclipse collection, this pull can be specified confidently wherever a matching 3 inch pattern handle is needed across a project.