GS2070 2-D Locking Device Set for GS2070 Under-Mount Slides

GS2070 2-D Locking Device For Precise Drawer Setup

GS2070 2-D Locking Device gives a GS2070 under-mount drawer slide a dedicated fine adjustment point, so installers can dial in drawer position without reworking the entire slide installation. Knape and Vogt engineers this locking device specifically for GS2070 under-mount slides, so the adjustment you make at the lever directly shifts the drawer relative to the slide hardware. The 2D release lever design provides targeted control in two critical directions - height and side-to-side - which directly affects drawer reveal consistency and front alignment across a run of cabinets. By adjusting from the locking device after the drawer is installed, you avoid pulling the drawer box or slides back out and keep other casework untouched. This focused adjustability helps installers handle common real-world cabinet conditions, from slightly out-of-square boxes to minor layout shifts, using the hardware already built into the GS2070 system.

Adjustment Features That Support Clean Drawer Lines

• The 2D release lever provides fine tuned height and side-to-side adjustments after the drawer is installed, so installers can correct minor alignment issues while the drawer remains in place.
• Height adjustment of plus 1/8 inch (3 mm) lets you raise the drawer front in small increments, which helps match reveals when cabinets or faces vary slightly from plan.
• Side-to-side adjustment of plus or minus 1/16 inch (1.5 mm) shifts the drawer horizontally, giving you control over gaps between fronts and adjacent doors or drawers.
• The set is designed as a locking device for GS2070 under-mount slides, so the adjustments are directly tied into the slide mechanism for predictable movement.
• Shims are specified for use with 1/2 inch drawer material thickness, helping align the locking device and slide interface when working with that common drawer side dimension.

Locking Device Adjustment Workflow After Installation

The 2D release lever makes fine tuned height and side-to-side adjustments after the drawer is installed, so the installer can work from the finished cabinet face instead of the interior. When a drawer front sits slightly low, the plus 1/8 inch height adjustment range lets you bring it up in controlled steps rather than remounting the drawer box. If the drawer front edges do not track evenly with neighboring fronts, the plus or minus 1/16 inch side-to-side adjustment lets you nudge the position until gaps look consistent. Because these changes happen at the locking device on the GS2070 under-mount slide, each tweak translates directly into front movement without disturbing slide setback or case mounting points.

Using The GS2070 2-D Locking Device In Cabinet Runs

Where This GS2070 Locking Device Is Applied

This GS2070 2-D Locking Device set for GS2070 under-mount slides is applied at the slide connection point on GS2070-equipped drawers, so it becomes the primary adjustment zone once the drawer is operating. In a cabinet run using GS2070 under-mount slides from Knape and Vogt, the locking device sits between the slide and drawer box, governing how the box registers to the hardware. Installers working with 1/2 inch drawer material thickness can use the specified shims to align the locking device plane with the drawer side, which supports predictable slide engagement. Because the 2D release lever is integrated into this locking device, adjustments in height or side-to-side movement occur exactly where the drawer and slide interact, giving a direct response to each small change.

Why These Two-Direction Adjustments Matter On Site

The height adjustment of plus 1/8 inch (3 mm) on the GS2070 2-D Locking Device is engineered around the small corrections typically required on finished cabinetry, allowing installers to level a drawer front relative to a face frame or adjacent fronts without rebuilding joinery. Side-to-side adjustment of plus or minus 1/16 inch (1.5 mm) is enough to tighten or relax reveals between drawer fronts, which helps present a uniform gap line across stacked drawers and doors using the same GS2070 under-mount slide system. Having the 2D release lever provide these adjustments after installation reduces time spent on layout corrections, because the drawer rides on the same slide while its position is refined. When working with 1/2 inch drawer material thickness, the specified shims bring the locking device and slide into proper relation, supporting consistent adjustment behavior across every drawer that uses this configuration.

Common Questions About GS2070 2-D Locking Device Use

Select This GS2070 Locking Device For Precise Adjustment

The GS2070 2-D Locking Device set for GS2070 under-mount slides from Knape and Vogt gives installers a defined point for height and side-to-side fine tuning after the drawer is installed, using the 2D release lever to control drawer front alignment. With plus 1/8 inch (3 mm) height adjustment and plus or minus 1/16 inch (1.5 mm) side-to-side movement, this 2070-2D-RL configuration supports the reveal and gap corrections typically needed on finished cabinetry. For drawer boxes built with 1/2 inch material thickness, the specified shims bring the locking device into the correct relationship with the drawer sides. Selecting this GS2070-focused adjustment hardware aligns the drawer front position directly through the under-mount slide system.