Olympus Pin Tumbler Cam Lock, DCN2 7/8" Material Thickness with 3/4" Cylinder, Oil Rubben Bronze, Keyed Alike - 107

Olympus Pin Tumbler Cam Lock For Secure Cabinets

Olympus pin tumbler cam lock DCN2-10B-107 is a cam lock with a zinc die cast body and zinc die cast pin tumbler cylinder, so the core components follow a stable metal construction that supports consistent key operation in regular cabinet use. The lock uses an N Series keyway equivalent to National D4291 4-pin or D4292 5-pin systems, which helps align it with common N Series keying layouts used across many installations. The standard function keeps the key removable in both locked and unlocked positions, allowing installers to remove the key after cycling the lock without changing existing workflow habits. The product is keyed alike as KA107 within the stock KA# range, so every KA107 lock in that series responds to the same key cut for simplified key management where a single key pattern is desired.

Cam Lock Details That Support Daily Use

• The body and cylinder are zinc die cast, which provides a rigid housing for the pin tumbler mechanism and supports repeatable cam rotation under normal operating torque in cabinet and casework settings.
• The N Series keyway, equivalent to National D4291 4-pin or D4292 5-pin, ties the lock to a defined key system, which matters when matching keying patterns across multiple locks in the same facility or project.
• The lock is easily rekeyable via a cylinder retainer clip, letting locksmiths or shops change keying without replacing the entire cam lock body, which supports long-term key system updates on existing casework.
• The product passed ANSI/BHMA A156.11 Grade 1 performance requirements and is equivalent to E07261 / E07271, which signals that the cam lock meets a recognized performance level for cam locks in demanding service.
• The Woodwork Institute acknowledges the product, so it aligns with WI-recognized hardware options often referenced in woodworking and architectural casework jobs where specified products are required.
• The key is removable in the locked or unlocked position, allowing users to set the desired state, withdraw the key, and leave the lock as configured without needing a dedicated key-retention procedure.

Installation And Face Coverage For Clean Fit

The lock uses a 1 inch face that covers splintering around the cylinder bore, so the front trim masks minor edge breakout on the door or panel and removes the need for an extra trim ring in many installations. The face design keeps the visible portion of the lock tight to the surrounding surface, which supports a neater finished appearance on cabinet fronts and casework. The oil rubbed bronze 10B finish provides a dark, traditional appearance on the face, which can coordinate with other 10B finished hardware on doors and cabinetry in the same project.

How This Olympus Cam Lock Works In Practice

Where This N Series Cam Lock Is Applied

The product is an Olympus Lock, Inc. cam lock in the Locks and Latches category, placing it in typical cabinet and casework security roles where a rotating cam secures a door or drawer. The cam lock uses two reversible cams that work in all positions, so the same lock body supports multiple cam orientations to match different door swings or latching directions on furniture and cabinets. One cam is straight and one is offset reversible, giving different throw offsets for the same cylinder centerline, which helps align the cam tip with a fixed strike or frame edge. The anti-rotation plate supports the body against spinning in the mounting hole, so the torque from normal key operation translates into cam movement instead of housing rotation. The lost-motion cam shifter lets the installer adjust the rotational relationship between cylinder and cam sequence, so the cam start and stop positions can be tuned to the door and frame geometry in a given installation.

Why Grade, Keying, And Finish Matter On Site

The lock passed ANSI/BHMA A156.11 Grade 1 performance requirements, so its design is tested against a defined cycle and load standard for cam locks, which matters when the lock will see frequent daily use in commercial or institutional casework. Keying can be matched with other N Series locks, allowing one N Series key system to operate multiple locations where the same keyway is desired. Stock keying supports both KD and KA with 4-pin standard layouts, while masterkeyed setups use 5-pin standard, giving projects the option of individual keys, shared keys, or hierarchical keying structures using the same basic cylinder family. Stock keyed alike numbers 101, 103, 107, and 915 let buyers select a known KA series, and the KA107 version keeps every KA107 cylinder on the same cut pattern, which simplifies service and day-to-day key handling. The oil rubbed bronze 10B finish ties the cam lock to a specific finish code that matches 10B hardware families, so casework designers can coordinate lock faces with hinges, pulls, and other visible components in the same color range.

Common Questions About The DCN2-10B-107 Cam Lock

Choose The Right Olympus Cam Lock For Your Job

The Olympus pin tumbler cam lock DCN2-10B-107 combines a zinc die cast body, N Series keyway, and ANSI/BHMA A156.11 Grade 1 performance to support cabinet and casework applications using a tested cam lock platform. Two reversible cams work in all positions together with an anti-rotation plate and lost-motion cam shifter, so the same lock body adapts to different door layouts and latch points. The 1 inch face and oil rubbed bronze 10B finish help the lock present cleanly on the cabinet front while matching related hardware finishes. Selecting this keyed alike KA107 version aligns multiple locks to one key pattern, streamlining key management wherever a shared key is preferred.