Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Knape and Vogt 24 inch drawer slides deliver full extension travel, so the drawer opens the full slide length and exposes the entire drawer box for easier access during cabinet use and layout work. The 8650FMB 24 model is a side mount ball bearing slide, which positions on the drawer side and cabinet wall, giving installers a familiar mounting style for face frame or frameless projects that already use side-mounted hardware. These slides are rated for 150 lb, and that load capacity supports heavier drawer contents in shop, garage, or cabinet storage where dense items are common. A soft close function on this slide slows the closing stroke and pulls the drawer shut, which helps reduce slamming and can limit shock to joinery over time. KV Model #8650FM is made in USA, providing a clearly identified manufacturing origin for projects that call out domestic components.
This 8650FMB 24 slide is described as a side mount design, so it references to the cabinet side and drawer side during install, aligning with standard side-mounted layouts in many shop workflows. Side clearance of 1/2 inch plus 0.1 inch minus 0 inch per side defines a fixed drawer box width relative to the cabinet opening, which supports consistent drawer sizing when repeating a bank of cabinets. With a 2 inch slide height, installers can design drawer sides and internal clearances so the hardware sits low enough to avoid rubbing but high enough to carry the load as intended. The recommended fasteners are #7 x 1/2 inch Phillips pan head screws, which informs drill sizes and driver choice when setting up jigs or power tools.
The 24 inch full extension length suits base cabinets, shop drawers, and storage units built around a nominal 24 inch depth, so the drawer can travel its full length and present contents clearly across the slide stroke. Because the slide is a side mount ball bearing design, it matches cabinet runs already laid out for side-mounted hardware, allowing consistent mounting locations on stiles or cabinet sides. The 32 mm pattern aligns with cabinets drilled on the 32 mm system, so the slide can locate on pre-drilled rows rather than custom measurements, which can tighten workflow when repeating casework. Zinc finish on the slide provides a bright, easily visible rail, which helps during alignment and checking for even extension across multiple drawers in a bank.
The specified side clearance of 1/2 inch plus 0.1 inch minus 0 inch each side gives a precise target for drawer box width, so once one opening is dialed in, the same dimensions apply across the run. A 2 inch slide height provides a known vertical footprint, letting drafters and builders set drawer side heights and cut lists without guesswork around clearance. The butterfly disconnect lever creates a clear release action, so drawers can be pulled off the cabinet members for finishing or adjustments and then returned to the same track alignment. The 150 lb rating works with heavier contents, which means the slide selection can remain the same from lighter kitchen drawers to denser tool or supply storage built around similar carcasses. With the 8650FMB 24 identified as KV Model #8650FM and made in USA, reordering the same slide for additional cabinets or replacement stays straightforward across future jobs.
The Knape and Vogt 8650FMB 24 slide is a 24 inch, side mount, full extension, soft close ball bearing drawer slide, so it supports smooth travel and closing on a standard side-mounted layout.
The 8650FMB 24 slide uses 1/2 inch plus 0.1 inch minus 0 inch side clearance on each side, guiding the drawer box width relative to the cabinet opening for consistent fitting.
The 8650FMB 24 drawer slides have a 150 lb rating, which supports heavier drawer contents in cabinets or shop storage built around the 24 inch slide length.
The butterfly disconnect lever on the 8650FMB 24 slide allows the drawer member to release from the cabinet member, simplifying cabinet mounting, finishing, and later adjustments.
The web description recommends #7 x 1/2 inch Phillips pan head screws for the 8650FMB 24 slides, guiding bit selection and driver setup for consistent installation.
The 8650FMB 24 slide is listed with a 32 mm pattern, so it aligns with cabinets drilled on a 32 mm system and can mount using existing system hole spacing.
The Knape and Vogt 24 inch drawer slides in the 8650FMB 24 version combine full extension, soft close action, 150 lb rating, and side mount installation, giving cabinet builders a clearly defined hardware choice for 24 inch deep drawers. Side clearance of 1/2 inch plus 0.1 inch minus 0 inch and a 2 inch height translate directly into drawer box dimensions, which supports accurate planning and cutting. With the 32 mm pattern and zinc finish, these slides align with common cabinet systems and shop standards, so they can be specified with confidence for repeat work or coordinated projects.
Sold In: 1 Set
