Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
1/4" NPT mini air station desiccant filter from Milton Industries is a pre-assembled filter/regulator/lubricator class unit that dries and regulates compressed air, helping air tools and air systems run with more consistent pressure and dryer air in one compact setup. The integrated desiccant dryer removes moisture from the air stream, which helps reduce water-related issues in air-operated tools and small pneumatic setups. The built-in regulator lets you set outlet pressure off your main line, giving finer control where work actually happens. A gage is already part of the unit, so line pressure can be read at a glance without adding separate components. This miniature air station clips easily to a belt, allowing the assembly to stay close to the operator or work area for portable air regulation. As an air line component, it fits into filter/regulator/lubricator workflows where moisture control and local pressure regulation are needed.
The Milton Industries S-1174 mini air station uses 1/4 inch male and female national pipe thread ports, so it can be threaded directly into a 1/4 inch NPT air line and then out to a hose or tool, keeping the assembly compact. With a maximum pressure of 125 pounds per square inch, the station is built for use on typical light industrial and shop air systems operating at or below that level. A maximum flow rating of 15 standard cubic feet per minute defines the air volume it supports, matching it to small air tools and point-of-use drops rather than high-volume equipment. Because the unit is pre-assembled with gage and regulator, there is no need to match separate regulator and gage bodies for these pressure and flow ranges, which keeps installation steps more straightforward.
The Milton Industries S-1174 mini air station is an air line component in the filters, regulators, lubricators class, so it fits naturally into compressed air runs where air quality and pressure need improvement close to the work. Its miniature format and belt clip design let it sit near an operator, so the desiccant dryer and regulator stay near nailers, staplers, or other small tools fed by a 1/4 inch line. The 1/4 inch MNPT and FNPT ports connect it between an existing supply and a downstream hose, positioning the desiccant dryer and gage where air leaves the main system. A 125 PSI maximum pressure aligns with many shop compressors, so it can sit on branches that serve small benches, assembly areas, or light-duty stations. With a maximum of 15 SCFM, it fits work where moderate air demand needs cleaner, drier air rather than bulk plant distribution.
The desiccant dryer in this mini air station removes moisture from the compressed air, which helps reduce water carryover to tools, valves, and work surfaces during use. That moisture reduction matters where finish quality or tool internals are sensitive to water in the air line. The integrated regulator controls outlet pressure from the 125 PSI-rated supply, so air tools can run at a pressure closer to their recommended range while still drawing from a higher-pressure main line. Having a gage visible at the station lets operators read actual working pressure at the point of use, supporting consistent settings between shifts or tasks. Because the station is pre-assembled, the regulator, gage, and desiccant dryer operate as a matched group around the 15 SCFM rating, which supports repeatable performance every time the mini air station is moved to another drop or workstation.
The Milton Industries S-1174 mini air station filters, dries, and regulates compressed air at the point of use, so tools receive dryer air at a controlled pressure for consistent operation.
The 1/4 inch male and female NPT ports let the mini air station thread directly into a 1/4 inch line and out to a hose or tool, keeping the assembly compact along the air run.
The 125 PSI maximum pressure rating means the mini air station is suited to light industrial or shop air systems operating at or below 125 PSI on the connected line.
The 15 SCFM maximum flow points this mini air station toward small air tools and point-of-use drops, matching applications that do not exceed this airflow demand during operation.
The desiccant dryer in this air station removes moisture from compressed air, helping reduce water reaching tools and workpieces where moisture could affect finishes or tool life.
The pre-assembled mini air station arrives with gage, regulator, and desiccant dryer already integrated, so installers connect the 1/4 inch ports and begin using localized air control right away.
The Milton Industries 1/4 inch NPT mini air station desiccant filter S-1174 brings a desiccant dryer, regulator, and gage together in one pre-assembled, belt-clippable unit, with 1/4 inch MNPT and FNPT ports, 125 PSI maximum pressure, and 15 SCFM flow capacity. For air line layouts needing localized drying and pressure control near smaller tools, this configuration offers a compact way to add those functions. Add the S-1174 mini air station at the points in your system where drier, regulated air will improve day-to-day compressed air performance.
Sold In: 1 Each