Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
BTK-UB shelf compact bracket from Sugatsune America is a shelf bracket designed with a height less than half that of the BTK type, so it supports shelving while keeping the vertical profile low for projects where clearance under the shelf matters. Its compact design with a short mounting bracket gives solid support in a small footprint, which helps when layout space on cabinet sides or walls is tight. The bracket is 199mm long and finished in white, so it matches the stated length while suiting light-colored closet or garage interiors. A strong and safe design helps the bracket handle typical shelf loads in its class, which supports confidence when using it in storage or organization layouts. The design fits perfectly at the corner, so it aligns with shelf edges and walls for clean, square installations.
The opening angle is slightly more than 90 degrees, which allows the bracket to resist inclination due to load when used as a shelf bracket, helping the shelf stay level when weight is applied. This geometry matters when installing multiple brackets under one shelf because it supports consistent alignment under loading. The compact design with a short mounting bracket focuses mounting points close to the corner, which can simplify drilling and fastening on narrow cabinet sides or wall studs. A raised countersunk head wood screw is specified, so the screw head sits flush in the countersink, helping the bracket seat tightly against the mounting surface for solid contact.
The BTK-UB shelf compact bracket, with its 7-13/16 inch depth and 3-15/16 inch height, works where a relatively deep shelf is needed but vertical clearance below the shelf is limited, such as under counter runs or in low-visibility storage zones. Its height being less than half of that of the BTK type means it occupies less space under the top board, which is useful when tooling, bins, or hanging items need room beneath the shelf. The bracket perfectly fitting at the corner helps in closet, shelving, or garage organization runs where shelves terminate at walls, because it supports the front and side edges right at the junction. The white finish aligns well with white melamine shelving or painted storage systems, which helps projects maintain a consistent visual line along the wall.
The opening angle slightly more than 90 degrees is designed to prevent inclination due to load when using the part as a shelf bracket, so as weight builds on the shelf the hardware geometry helps resist sagging at the hinge point. This behavior supports repeatable, level shelf results across a run when brackets are mounted at the same height. The compact design with short mounting bracket keeps fastener locations tight to the corner, which simplifies using common drilling jigs or templates for consistent bracket placement from shelf to shelf. The strong and safe design supports confidence when laying out storage that may see varying loads over time, because the bracket is engineered with load resistance in mind. Specifying a raised countersunk head wood screw means the fastener head draws into the bracket and nestles flush, which reduces interference with the shelf material and keeps the bracket bearing evenly against wood surfaces for reliable performance.
The BTK-UB shelf compact bracket measures 7-13/16 inches deep and 3-15/16 inches high, which sets the supported shelf depth and the amount of vertical space it occupies under the top board.
The BTK-UB bracket height is less than half that of the BTK type, so it leaves more open area below the shelf for storage, access, or clearance in closet, cabinet, or garage installations.
The BTK-UB bracket uses an opening angle slightly more than 90 degrees to prevent inclination due to load when used as a shelf bracket, helping the shelf stay level as weight is applied.
The BTK-UB compact bracket is designed to fit perfectly at the corner, so it sits where the shelf meets the wall and supports both the depth and edge at that junction.
The BTK-UB bracket specifies a raised countersunk head wood screw, which allows the screw head to sit into the countersink and pull the bracket firmly against the mounting surface.
The BTK-UB compact design with a short mounting bracket keeps fastener positions close to the corner, which can simplify drilling and alignment on narrow cabinet sides or wall studs.
The BTK-UB shelf compact bracket from Sugatsune America combines a height less than half of the BTK type with a 199mm long support arm, so it suits projects needing both deep shelving and extra room under the top board. Its strong and safe design and opening angle slightly more than 90 degrees support level, dependable shelves under load. The compact, short mounting bracket and white finish help it integrate cleanly into closet, cabinet, or garage organization systems. Choose this bracket when shelf depth, corner fitting, and under-shelf clearance all factor into the layout.
