DSR403 concealed door straightener is designed to protect doors from future warping, so fabricated doors keep a flatter surface over time in typical passage door applications. This 1524mm model is part of Sugatsune's DSR403 series, which is installed at the time of manufacturing to prevent warping rather than trying to correct it later. The straightener is fully concealed and hidden in use, so the hardware does its job without changing the visible appearance of the door. Its plain/nickel finish is paired with a cover cap, which maintains a clean look around the adjustment point. As a passage door hardware component, it fits naturally into builders hardware workflows where long doors or laminate-faced doors are prone to movement from environmental changes.
This DSR403 concealed door straightener is recess mounted under laminate, so a groove is prepared in the door core and the straightener is set into that recess before the laminate is applied. The pressure-fit design holds the unit in position without screws, simplifying installation into the machined channel and avoiding extra fastener layout. A minimum door thickness of 18mm, or 11/16 inch, aligns the product with common engineered and laminate door constructions using that thickness. Once installed, plus or minus 10mm of adjustment is made from the top of the door using an M4 Allen key, so the straightening force is tuned after the door is assembled and hung. The straightener can be cut from the bottom by up to 420mm, or 16-9/16 inch, which allows trimming to suit specific door heights while keeping the top adjustment area intact.
This 1524mm DSR403 concealed door straightener from Sugatsune America is classified under passage door hardware, so it is suited to doors used for standard passage openings where warping control is important. Installation at the time of manufacturing positions the straightener inside the door structure before the laminate goes on, so the hardware becomes part of the door rather than an external add-on. Because it is recess mounted under laminate, the straightener fits well into laminated door builds in commercial or residential projects where a flat door face is desired. The ability to cut the straightener from the bottom by up to 420mm lets fabricators adapt one length to different door heights while keeping the adjustment access at the top. This flexibility supports jobs with multiple door sizes that still share the same construction approach.
The plus or minus 10mm adjustment range on the DSR403 concealed door straightener allows installers to apply controlled tension from the top of the door, which helps counteract existing or developing warp within that range. Using an M4 Allen key from the top keeps the adjustment point accessible after the door is hung, so corrections can be applied while the door remains in place on its hinges. Because the straightener is pressure-fit into its recess, the load is transferred along the groove walls rather than through screws, supporting consistent engagement over the length of the unit. Its fully concealed design keeps the mechanism hidden, so appearance is maintained even when adjustments are made over time. Integrating the straightener under laminate locks the hardware against the door core, which helps the door and straightener act together when resisting bowing forces.
The DSR403 concealed door straightener is specified for a minimum door thickness of 18mm, or 11/16 inch, aligning it with many laminated and engineered door constructions using that thickness.
The DSR403 straightener is recess mounted under laminate and pressure-fit into place, so it sits in a machined groove within the door core and is then covered by the laminate layer.
This concealed door straightener offers plus or minus 10mm of adjustment from the top of the door using an M4 Allen key, allowing tuning of the straightening force on the installed door.
The 1524mm DSR403 door straightener can be cut from the bottom by up to 420mm, or 16-9/16 inch, so it can suit various door heights while keeping the top adjustment area intact.
This door straightener is recess mounted under laminate and fully concealed within the door, with a cover cap at the top in a plain/nickel finish to keep the visible area clean.
This DSR403 straightener is designed to be installed at the time of manufacturing, so it is integrated into the door structure before the laminate is applied to help prevent future warping.
The DSR403 concealed door straightener with cover cap in plain/nickel from Sugatsune America combines a 1524mm length, recess-mounted under-laminate design, and plus or minus 10mm top adjustment to address door warping at the manufacturing stage. Its pressure-fit, fully hidden installation and suitability for 18mm thick doors align with common laminate and engineered door builds. For passage door projects where flat faces and clean hardware lines are required, this door straightener offers a way to integrate warp control directly into the door structure during fabrication.
Sold In: 1 Package