Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
1524mm concealed door straightener gives passage doors a built-in method of controlling future warping by tying a rigid, adjustable member into the door structure. This matters when long doors need to stay straight over time in normal use. Sugatsune America designs this straightener for concealed use, so the component remains hidden while still correcting bow in the door leaf. That keeps visible door faces clean while still delivering functional straightening performance. The straightener is part of Sugatsune's DSR series, which is installed at the time of manufacturing to prevent warping in service. That timing places the control hardware inside the door from day one, helping maintain alignment with frames and latches as conditions change. A cover cap in a plain/nickel finish protects the adjustment area while leaving a neat, finished appearance on the working edge.
Recessed mounting under laminate means this straightener sits inside a machined pocket, so it aligns flush with the door core while remaining hidden behind the finish layer. That simplifies later finishing steps because the surface profile stays consistent. A fully concealed or hidden configuration places the straightener where it cannot be seen in normal operation, keeping the focus on the door design while the hardware works internally. Plus or minus 10 mm adjustment is available from the top of the door using an M4 Allen key, so the correction force can be tuned after installation from a single access point. That adjustment range allows fine tuning of bow over the door length, which is especially useful when environmental changes introduce minor twist or curvature.
This Sugatsune America 1524mm straightener is specified for doors with a minimum thickness of 12 mm, so it aligns well with thin construction where core depth is limited. That matters for lightweight or laminate-faced doors that still need warp control without over-sizing the leaf. Recessed mounted under laminate design places the straightener along the door length, which suits tall passage doors needing continuous support across a 48-64 inch span. As passage door hardware, the straightener integrates into interior door builds where predictable closing and latching depend on a flat edge meeting the frame. Fully concealed mounting lets it serve in visible interior locations because the corrective hardware does not compete with the design of laminates or veneers. The cover cap in plain/nickel finish protects the accessible adjustment zone while presenting a neutral, unobtrusive look at the access point.
Plus or minus 10 mm adjustment available from the top of the door with an M4 Allen key gives a clear quantitative range for bending control along the straightener. That defined movement helps installers and fabricators dial in correction in a repeatable way across multiple doors in a project. Top-of-door access means the adjustment interface sits where it can be reached even after the door is hung, so warping developed in service can be countered without removing the door from hinges. Optional mounting holes accept 4 M4 (U.S. #8) flathead countersunk wood screws, providing a positive mechanical connection between straightener and door. That screw-down option helps transfer corrective force effectively into the door structure over time. Classing this part within builders hardware and passage door hardware keeps it aligned with common trade practices, supporting consistent placement and adjustment procedures across different builds using the same DSR series.
The Sugatsune DSR423-1524-25 straightener is installed at the time of manufacturing to prevent door warping, helping passage doors stay aligned with frames for smoother operation.
This door straightener is recessed mounted under laminate, so it sits in a routed pocket inside the door core while remaining hidden behind the finished surface during normal use.
This straightener is specified for a minimum door thickness of 12 mm, allowing it to fit slim door constructions while still providing internal warp control along the door length.
The straightener offers plus or minus 10 mm adjustment from the top of the door using an M4 Allen key, letting installers fine tune door flatness after hanging.
Optional mounting holes allow fastening the straightener to the door using 4 M4 (U.S. #8) flathead countersunk wood screws, improving transfer of corrective force into the door structure.
This straightener is fully concealed or hidden and recessed under laminate, so it works inside the door while keeping visible faces clean, apart from the discreet top adjustment access.
This Sugatsune America 1524mm concealed door straightener offers recessed under-laminate mounting, plus or minus 10 mm adjustment from the top with an M4 Allen key, and suitability for 12 mm thick doors, giving fabricators a practical solution for managing passage door warping.
Sold In: 1 Package