
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
14 inch replacement dust collection bags give your JET DC-650 dust collector a fresh, clear lower collection bag matched to the original JET specification. The JET CB-5 clear plastic 14 inch diameter collection bag is built for the DC-650 unit, so sizing, mounting fit, and airflow performance all follow the factory setup. The clear plastic material lets you see dust levels as the 2-1/10 cubic foot capacity fills, which helps plan changeouts around actual shop use. The 23 inch collection bag length provides room for typical planer, jointer, and saw waste loads while keeping the bag manageable when it is time to swap. Airflow at 4 inches listed at 650 CFM describes how the bag works within the DC-650 system under standard conditions, so the replacement maintains the same movement of chips and fines as the original configuration.
The 14 inch diameter collection bag is specified to fit JET DC-650 dust collectors, so the bag interface is sized for that lower ring on the machine. The 23 inch collection bag length provides enough material to wrap and secure at the clamp area while still leaving capacity below for dust buildup. The 2-1/10 cubic foot volume pairs with the DC-650 performance, giving the bag enough space to match the 650 CFM airflow rating at 4 inches in typical dust collection layouts. The clear plastic material helps during installation by making folds and alignment lines visible around the ring, which supports an even clamp line and consistent sealing.
The JET CB-5 clear plastic 14 inch diameter collection bag is specified for JET DC-650 dust collector units, placing it directly in small to mid-size woodworking shop dust systems built around that machine. Within that setup, the 2-1/10 cubic foot capacity balances chip volume and bag change frequency, so the dust collector can serve planers, jointers, and table saws under the 650 CFM airflow rating at 4 inches. The 23 inch bag length matches the lower collector zone on the DC-650, supporting normal floor clearance while still leaving room for ducting and collection drums around the machine. The clear plastic construction maintains visibility of waste levels, which is helpful when the DC-650 is positioned against a wall or in a corner where direct access is limited.
The 30 micron efficiency rating defines how the JET CB-5 bag performs as the lower collection point in the DC-650 system. By capturing material down to that 30 micron range, the bag supports the overall dust collection stage specified for this machine class. In practice, this means chips and a substantial portion of fine dust generated at the connected tools are directed into the 14 inch diameter bag, which keeps the working area around the DC-650 cleaner during typical woodworking runs. Because the bag is matched to the DC-650 airflow and velocity at 4 inches - 650 CFM and 7,445 FPM - the system moves dust into the bag in line with original factory expectations.
The 14 inch diameter of the JET CB-5 bag matters for sealing against the DC-650 lower ring, as correct diameter supports consistent negative pressure and helps the 650 CFM airflow operate as specified at a 4 inch duct. When the bag diameter matches the machine, the 7,445 FPM air velocity at 4 inches can carry chips and fines directly into the 2-1/10 cubic foot capacity without turbulence from gaps at the bag joint. The 23 inch length gives the dust stream enough drop distance, so captured material can settle toward the bottom of the bag rather than staying in the throat area.
The 30 micron efficiency rating defines the threshold at which the bag holds particulate in the collection zone, which influences how much material reaches the bottom section during continuous operation. Combined with the clear plastic construction, this efficiency level allows operators to see how dust builds across the full bag height and use that visual reference to time changeouts. The JET Tools manufacturer part number JT9-709565 gives a precise reference in parts lists and maintenance logs, which supports consistent bag selection when servicing multiple DC-650 units across a facility.
The JET CB-5 clear plastic 14 inch diameter collection bag is specified to fit JET DC-650 dust collector units, so it matches that machines lower collection ring and airflow setup.
The collection bag capacity is rated at 2-1/10 cubic feet, giving a defined dust volume that aligns with normal use on a JET DC-650 under its stated airflow conditions.
The JET CB-5 collection bag length is 23 inches, which provides vertical space for dust accumulation while maintaining a workable size for handling and changes.
The dust collection bag is listed with airflow at 4 inches of 650 CFM and air velocity at 4 inches of 7,445 FPM, matching the JET DC-650 system performance data.
The JET CB-5 collection bag has an efficiency rating of 30 micron, which defines the particle size range it is specified to capture in the DC-650 system.
The clear plastic construction allows dust levels inside the 14 inch diameter bag to remain visible from the outside, supporting quick visual checks of remaining capacity.
The JET CB-5 clear plastic 14 inch diameter collection bag is specified for the JET DC-650 dust collector, with dimensions, capacity, and 30 micron efficiency matched to that system. When a replacement aligns with the original 650 CFM airflow, 7,445 FPM velocity at 4 inches, and 2-1/10 cubic foot capacity, dust moves and settles in the way the machine data describes. For shops running one or several DC-650 units, using the JT9-709565 part number anchors ordering to this exact 23 inch long collection bag. Select this JET Tools dust collection bag when the application calls for a clear, 14 inch diameter bag tuned to DC-650 performance.