Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
This Würth #7 x 1-1/4-inch modified pan head face frame screw is sized specifically for 3/4-inch face frame stock, where a clean-pulling joint and a non-wedging head make the difference between a tight connection and a split stile. Coarse thread, Type 17 auger point, square drive, and a lubricated finish come together in a screw built to run fast and seat right in softwood and sheet-good face frames.
Face frame work demands a screw that fits the stock. At 1-1/4 inches, this screw is the standard length for pocket-hole joints in 3/4-inch material: long enough to develop full thread engagement in the second member, short enough to stay clear of the face. The modified pan head sits across the pocket wall and draws the joint together without the wedging action that splits stiles. This is a coarse-thread screw, which means it is the right choice for softwood face frames, pine, plywood, MDF, and particleboard. For hardwood maple, oak, or cherry face frames, a fine-thread screw is the better fit.
The Type 17 auger point has a fluted tip that cuts into wood fibers as the screw advances, clearing material away from the tip and lowering the torque needed to drive the screw fully home. This is especially useful in production runs where driving hundreds of screws in a session adds up. The lubricated finish further reduces friction along the thread, so the screw moves into the pocket without fighting the material. The #2 square drive recess is designed to hold the screw on a correctly sized bit, which helps with one-handed placement when working inside a cabinet or at an awkward angle. Jar packaging holds 500 screws and includes a 2-inch drive bit.
Cabinet shops running softwood or sheet-good face frames will find this screw covers the most common joint in the production cycle: rail to stile, 3/4-inch stock, pocket-hole joinery. It is also a practical choice for attaching a softwood face frame to a cabinet box when the combined stock thickness calls for 1-1/4 inches. Residential cabinetmakers, small shops, and site installers who build or modify face-frame cabinets on the job will work through a jar of 500 quickly on a kitchen or bath project.
This is a coarse-thread screw, which is correct for softwood, pine, plywood, MDF, and particleboard face frames. Hardwood face frames in maple, oak, or cherry require a fine-thread screw to prevent splitting and maintain holding power.
A flat or bugle head acts like a wedge as it seats, which can split narrow face frame stock. The modified pan head bears against the pocket wall and pulls the joint together without driving into the grain.
Yes. Each jar of 500 screws includes a 2-inch #2 square drive bit.
This screw is designed for use in a pocket-hole joint where the angled pocket has already been bored. The Type 17 auger point helps the screw start cleanly at the bottom of the pocket without an additional pilot hole.
The lubricated coating reduces friction along the thread as the screw drives, which lowers the torque needed to seat the screw and makes a noticeable difference when running high volumes in a production setting.
When the stock is 3/4 inch and the frame is softwood, this is the screw that fits the job: the right length, a head that pulls without splitting, a point that starts clean, and a drive that holds the bit where you need it.
Sold In: 1 Jar
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  WW90210 Mfr# 0614176153961 1 | #2 x 1" Square Drive Insert Bit, 2 Piece Bit | ||||
Sold in: 1 Each |  WW90260 Mfr# 0614176143961 1 | #2 x 6" Square Drive Insert Bit, 2 Piece Bit |
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Jar |  WW17350-JAR Mfr# 3670000192961 500 | Würth #7 x 1-1/2" Modified Pan Head Face Frame Screw Square Drive - Type 17 Auger Point Coarse Thread Lubricated, 3670000192961 500 - 500/Box |