Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Dynabrade DynaCut Extreme sanding disc uses premium P graded aluminum oxide abrasives, which cut aggressively while keeping scratch patterns consistent, helping installers bring surfaces to a controlled 320 grit finish. The disc is built on a high performance 3 mil film backing, so it stays extremely tough and tear resistant as it runs over edges and contours common in shop and jobsite sanding. Its 6 inch diameter with hook and loop attachment and no hole design focuses the abrasive across the full face of the disc, supporting even contact on flat panels and parts. The proprietary clog free coating is pigment free, so it resists loading without transferring color, which matters when sanding light-colored materials or primers where contamination can telegraph through later coats.
The hook and loop attachment system on this 6 inch sanding disc allows it to be pressed onto a matching backup pad, locking in place through the hook and loop interface so the disc stays secure during use. This setup lets installers remove the disc without damaging the backing, so partially worn discs can be set aside and then reused when that grit is needed again. The 3 mil film backing keeps the disc stable on the pad while still conforming enough to follow light contours, helping maintain contact without wrinkling. With its no hole face, the disc sands uniformly across its surface on suitable pads, which supports predictable results on cabinet parts, panels, and trim pieces.
This Dynabrade DynaCut Extreme 6 inch 320 grit hook and loop no hole aluminum oxide on film sanding disc fits workflows that call for repeatable fine sanding on wood, composites, or similar materials where a 320 grit finish is specified. The abrasive is manufactured with a premium P graded aluminum oxide grain, so each disc behaves consistently from one to the next, which matters when multiple operators or stations are finishing parts to the same standard. The tough, tear resistant 3 mil film backing allows the disc to handle edge work, inside corners, and profile transitions that would challenge lighter paper-backed discs, helping maintain productivity as parts move through sanding stages.
The high performance 3 mil film backing generates the finest finishes and up to 4X the life of paper discs, so one disc can stay in service longer before performance drops, which reduces time lost to frequent disc changes. This longer life, combined with the proprietary clog free coating, means the abrasive surface stays open longer instead of loading with dust, so cut rate stays more consistent over the life of the disc. The pigment free nature of the coating avoids adding unwanted color during sanding, which supports clean, predictable results on lighter materials and finish systems. Because the hook and loop attachment lets discs be saved for future use when not completely worn, installers can keep partially used 320 grit discs ready for touchups or short runs, tightening control over material use and sanding quality across projects.
This disc is manufactured with premium P graded aluminum oxide abrasives, which supports fast cutting action while maintaining a consistent scratch pattern across the work surface.
The extremely tough, tear resistant 3 mil film backing keeps the disc intact around edges and contours, which helps extend disc life and maintain an even finish on detailed parts.
The proprietary clog free, pigment free coating creates a buildup resistant abrasive surface, so the disc loads less and reduces risk of color transfer on sensitive finishes.
The hook and loop attachment system allows quick disc changes and lets partially used discs be saved for future use, supporting flexible grit changes and reduced abrasive waste.
The 320 grit rating suits fine sanding stages where a smooth surface profile is needed before finishing, helping installers hit target sheen and coating build requirements.
The high performance 3 mil film backing generates up to 4X the life of paper discs, so fewer discs are consumed over the same amount of sanding work.
The Dynabrade DynaCut Extreme 6 inch 320 grit hook and loop no hole aluminum oxide on film sanding disc pairs premium P graded aluminum oxide grain with a high performance 3 mil film backing to deliver extended life in fine sanding stages. Its proprietary clog free, pigment free coating keeps the abrasive surface cutting cleanly, while the hook and loop attachment system supports quick changes and reuse of partially worn discs. For shops needing consistent 320 grit finishes with reduced disc turnover, this disc offers a film-backed option built for sustained performance across repeated sanding cycles.
Sold In: 1 Package