Corner square face wood pedestal foot gives a furniture base a defined support point at the corner, so casework or cabinets can stand on a solid, repeatable footprint. This 6 x 6 x 4-1/2 inch corner pedestal foot sits at the junction of two cabinet sides, creating a square support that follows the line of the case. The bun foot design places material where load transfers to the floor, helping keep bases consistent from piece to piece. Being made as a pedestal foot, it lifts the case off the floor by its 4-1/2 inch height, establishing a uniform toe or reveal band around the project. As part of the Pro Value Series, it aligns with trade-focused components chosen for everyday woodworking jobs. In decorative hardware and moldings work, a dedicated pedestal foot simplifies planning around base heights and transitions.
The 6 x 6 inch footprint gives clear reference edges for setting the foot flush with cabinet sides, which aids in squaring bases during assembly. Its 4-1/2 inch height defines the vertical offset, so installers can cut toe boards or paneling to meet that dimension without guesswork. Because it is a corner square face pattern, the inside faces meet at a right angle that follows typical cabinet construction, helping alignment when fastening from the case into the foot. As a bun foot within decorative hardware and moldings work, it can be planned into base layouts where continuous skirting or applied moldings need a consistent starting height. Unfinished cherry lets finishing steps happen after fitting, so scribing or minor shaping can be done first and then integrated into the final finish schedule.
This corner square face wood pedestal foot serves in decorative hardware and moldings projects where a defined corner support is needed under cabinets or furniture. The 6 x 6 inch plan size gives enough surface to meet typical cabinet side thicknesses and still present a square front profile, which matters when building traditional bases. With its 4-1/2 inch elevation, the foot can establish a recognizable furniture-style stance, so case pieces gain visual separation from the floor. As a bun foot in the Pro Value Series line, it suits pedestal-style bases on case goods, built-in cabinetry, or similar woodworking where discrete supports are used instead of full plinths. Cherry wood construction supports use alongside cherry face frames, doors, and trim, helping projects keep grain and color families aligned through the lower section of the piece.
The defined 6 x 6 x 4-1/2 inch dimensions let shops standardize jigs or stops for locating these feet, which supports consistent base reveal from unit to unit. Because it is a corner square design, layout lines can simply follow cabinet edges, so installers can reference from existing corners rather than re-establishing new geometry. The 4-1/2 inch height also interacts directly with base moldings or applied profiles in decorative hardware and moldings work, allowing those elements to be cut to one known height. Unfinished cherry gives finish departments control over stain intensity and topcoat sheen, so the foot can either blend with the main case or be toned slightly to balance light at floor level. As a bun foot, its concentrated support area pairs well with pedestal layouts where load transfers occur at key points rather than along full-length rails.
The pedestal foot measures 6 inches by 6 inches in plan and 4-1/2 inches high, so it creates a defined square footprint and a set elevation for cabinet or furniture bases.
The corner foot is made of unfinished cherry wood, which provides a cherry grain pattern ready for staining, clear coating, or painting to match surrounding casework.
The corner square face design aligns with the outside corner of a cabinet or furniture piece, so the foot follows both side faces and supports straightforward, square positioning.
As a bun foot in the pedestal feet category, it suits furniture-style bases on cabinets, case goods, or similar woodworking where discrete corner supports are preferred.
The unfinished wood surface allows shops to sand and apply their chosen finish system so the foot can match or coordinate with existing cherry components and finishes.
The Pro Value Series branding identifies this corner pedestal foot as part of a line selected for professional woodworking use, aligning it with trade-oriented decorative components.
The 6 x 6 x 4-1/2 inch corner square face wood pedestal foot in cherry gives projects a consistent base height and footprint using an unfinished cherry bun foot format. Its dimensions, material, and Pro Value Series designation suit decorative hardware and moldings work where a corner-mounted pedestal foot is the planned support. For cabinets or furniture built around cherry casework and a furniture-style stance, this dedicated pedestal foot provides a clear starting point for layout and finishing.