Domi Cam adjustable wing mounting plate gives cabinet builders a 3mm Salice mounting plate that positions the hinge precisely on the cabinet side, so door alignment can be set accurately on day one and maintained over time. As a hinge mounting plate in the Salice America line, it forms the base between cabinet and hinge arm, which matters when repeatable cup drilling patterns and consistent reveals are part of the job. Die-cast steel construction provides a solid platform for hinge loading, helping the door swing feel consistent across multiple openings in the same run. Nickel plating resists corrosion, so the plate keeps performing in typical kitchen and bath environments where moisture and cleaning products are common. As part of the Salice hinge system, this plate supports a stable connection that helps doors close smoothly on series 100, 200, 400, F, M, universal, and Silentia hinges.
This Salice hinge mounting plate uses pre-mounted Euro screws on the cabinet side, so it drops directly into standard Euro-style system holes and pulls tight without layout work. The 3mm plate height establishes a consistent hinge position off the cabinet surface, important when setting uniform reveals across a wall of doors. Two cam adjustment built into the plate provides plus or minus 2 mm of cam height movement, letting the installer raise or lower the door relative to the cabinet quickly. Cam depth adjustment from -0.5 mm to +2.8 mm then shifts the door in or out, which helps flush the door to the face of adjacent fronts without shifting the carcass. Together these adjustments turn the plate into the primary fine-tuning point for the Salice hinge system.
This hinge mounting plate is specified as a 3mm plate, so it suits cabinet runs where that plate height is part of the hinge layout and drilling pattern. As a Domi Cam adjustable wing mounting plate within the Salice America program, it is used on cabinets that carry Salice hinges in series 100, 200, 400, F, M, universal, and Silentia, giving installers a single plate style to support multiple hinge series. The cabinet side fastening method uses pre-mounted Euro screws, which fits production cabinets bored for Euro screws and lets the plate be driven home quickly on the line or on site. Because the plate is made from die-cast steel with nickel plating, it works well in kitchen, bath, and casework installations where a metal base is needed under the hinge arm and resistance to corrosion matters over the life of the project.
The two cam adjustable hinge mounting design provides cam height adjustment of plus or minus 2 mm, which means the door can be shifted up or down at the plate rather than adjusting the carcass or redrilling hinge cups. This saves time during fitting, especially on stacked doors where reveals need to stay even. Cam depth adjustment ranging from -0.5 mm to +2.8 mm lets the installer move the door closer to or further from the cabinet face at the plate, which helps correct minor variations in door thickness or carcass build without altering the hinge arm. Using one mounting plate for Salice series 100, 200, 400, F, M, universal, and Silentia hinges keeps the adjustment approach consistent across the job, so once the cams are understood, the same technique applies everywhere. Because the plate is die-cast steel with nickel plating, those cams work against a sturdy, corrosion-resistant body, supporting repeated adjustments during initial setup and later service.
The BARGR39/20 part is a Domi Cam adjustable wing hinge mounting plate from Salice America, so it serves as the interface between cabinet side and Salice hinge arm in a concealed hinge system.
This hinge mounting plate is for Salice series 100, 200, 400, F, M, universal, and Silentia hinges, allowing the same plate style to support several hinge families on a project.
The hinge mounting plate has cam height adjustment of plus or minus 2 mm and cam depth adjustment of -0.5 mm to +2.8 mm, so doors can be finely tuned without moving the cabinet or redrilling.
The Domi Cam adjustable wing mounting plate uses pre-mounted Euro screws on the cabinet side, which suits system-bored cabinets and speeds hinge plate installation in production or retrofit work.
The hinge mounting plate is constructed of die-cast steel with nickel plating, providing a rigid base for the hinge arm and resistance to corrosion in typical cabinet environments.
The 3mm specification refers to the plate height, so it sets the hinge arm a defined distance off the cabinet surface, supporting consistent reveals when used with the matching Salice drilling pattern.
The Domi Cam adjustable wing mounting plate from Salice America gives you a 3mm Salice mounting plate that works with series 100, 200, 400, F, M, universal, and Silentia hinges, so one plate style can cover a wide range of cabinet runs. Die-cast steel with nickel plating provides a dependable base under each hinge arm, while pre-mounted Euro screws let the plate lock into standard system holes quickly. With cam height adjustment of plus or minus 2 mm and cam depth from -0.5 mm to +2.8 mm, this hinge mounting plate supports precise door alignment on new installations and later adjustments on service calls.
Sold In: 1 Each