EPCO free swinging glass door hinge, screw-on polished chrome - 510-PC is a shallow channel glass door hinge that supports 1/4 inch and 3/16 inch glass, giving installers a single hinge solution for these two common glass thicknesses. The shallow channel design grips the glass edge while keeping the profile minimal, which helps when you are fitting doors into tight cabinet reveals or slim face frames. A polished chrome finish on the hinge presents a clean, bright look on visible cabinet fronts or display cases where hardware appearance matters to clients. This hinge is part of EPCO's glass door hinge line, so it is purpose-built for framed or frameless cabinet doors that use glass panels. By matching the hinge directly to 1/4 inch or 3/16 inch glass, you reduce trial fitting time and keep your layout consistent across a run of doors.
This EPCO screw-on polished chrome glass door hinge uses a 5 mm pin that seats into a plastic bushing set in an 8.5 mm hole, giving you a clear drill dimension when laying out cabinet frames or side panels. Because the plastic bushings press-fit into the 8.5 mm hole, you can drill your frames or case sides, insert the bushing, and then drop the hinge pin in without extra fitting steps. The shallow channel around the glass edge lets you position 1/4 inch or 3/16 inch glass accurately in the hinge channel before tightening the hinge connection, which supports clean reveals on cabinet fronts. With a screw-on design, the hinge mounts to its plates using driver-friendly fasteners, helping you tie hinge installation directly into your standard case assembly sequence.
This EPCO free swinging glass door hinge is designed for 1/4 inch and 3/16 inch glass, making it a fit for cabinet doors and display cases built around these two panel thicknesses. The shallow channel construction seats along the glass edge while keeping hardware bulk low, which is helpful on narrow stiles or light casework where larger hinges would crowd the opening. Plastic bushings that press-fit into an 8.5 mm hole are intended for the cabinet frame or case material, so the hinge works well where you can bore accurate 8.5 mm holes in side panels or face frames. The 5 mm pin on the hinge slides into these bushings, forming a pivot that suits free swinging doors on cabinets, display units, or similar woodworking projects that need a simple open-and-close movement.
The defined 8.5 mm hole size for the plastic bushings allows you to set up drilling jigs or line-boring equipment once and repeat the same pattern across a full bank of cabinets, which improves speed and consistency. Because the hinge is specified for both 1/4 inch and 3/16 inch glass, you can standardize your hinge choice across jobs that vary glass thickness while keeping the same door overlay plan and hinge spacing. The 5 mm hinge pin working with the press-fit bushing helps keep swing action centered, which supports even gaps between paired doors and alignment with adjacent casework. A polished chrome finish gives the hinge a finished look on exposed glass doors, so you can fit hardware in retail, office, or residential cabinetry without needing separate decorative covers. With its screw-on connection, this hinge ties into normal driver-based installation routines, reducing changeover time between different cabinet hardware tasks.
The EPCO 510-PC glass door hinge is designed for 1/4 inch and 3/16 inch glass, so it suits cabinet or display doors built around these two common glass thicknesses.
The hinge uses a 5 mm pin that fits into a plastic bushing press-fit into an 8.5 mm hole, creating a defined pivot point for consistent door swing on cabinet frames.
The plastic bushings for the EPCO 510-PC hinge press-fit into an 8.5 mm hole, allowing you to use standard boring equipment set to that single dimension.
The EPCO 510-PC is a screw-on polished chrome glass door hinge, so it fastens using driver-installed fasteners during cabinet or display case assembly.
The shallow channel glass door hinge grips the glass edge without adding bulk, helping keep reveals tight and clear on slim cabinet frames and light casework.
The EPCO free swinging glass door hinge, 510-PC, has a polished chrome finish, allowing it to coordinate visually with other bright cabinet hardware.
The EPCO free swinging glass door hinge, screw-on polished chrome - 510-PC gives you a shallow channel hinge matched to 1/4 inch and 3/16 inch glass, a 5 mm pin, and plastic bushings for an 8.5 mm hole. For cabinet and display work using these glass thicknesses, this setup supports consistent drilling, reliable pivot action, and a clean polished chrome appearance. Add this hinge to your next glass door run when you need a screw-on solution that fits directly into 8.5 mm bored frames and matches both 1/4 inch and 3/16 inch glass panels.
Sold In: 1 Each