Epco 522-B shelf support uses a 5 mm pin to locate securely in a matching hole, which keeps cabinet or closet shelves seated at a consistent height for straightforward layout work. The bright brass finish identifies the support clearly against lighter interiors, helping installers spot each point quickly during fitting or adjustments. Stamped steel construction creates a solid bearing surface for the shelf edge, so point loads transfer cleanly into the cabinet side rather than deforming softer materials. The 0.75 inch length provides a defined ledge under the shelf, which helps align the shelf front to cabinet faces during installation and later resetting. Sold each, this support suits jobs where individual positions are added, replaced, or adjusted one at a time, which is useful in service work or small custom runs.
This shelf support uses a 5 mm pin, so it seats into 5 mm diameter holes typically bored in cabinet and closet gables, allowing straightforward push-in installation during assembly. The 0.75 inch length sets a predictable projection into the cabinet, which simplifies drilling depth decisions and helps keep shelves flush from left to right. The bright brass finish visually confirms that each support is fully seated against the panel surface, which reduces the chance of uneven shelf corners in finished work. Stamped steel construction gives the support a defined shape that registers under the shelf edge, helping installers feel when the shelf is fully engaged before fastening or loading.
This Epco 522-B shelf support belongs in cabinet, closet, and general shelf organization projects that use 5 mm system holes, because the 5 mm pin engages those bores directly. The stamped steel body is shaped to sit against the cabinet side, creating a firm ledge for adjustable melamine, plywood, or composite shelves used in many shop-built or modular systems. With a 0.75 inch length, the support works well in carcasses where shelves sit close to face frames or doors, since the projection stays within common cabinet depths. The bright brass finish matches other brass-toned hardware visually, which helps keep a consistent interior look when projects specify brass-colored components.
The 5 mm pin on this shelf support provides a repeatable locating point, so each support references the same drilling line and keeps shelves level across a run of cabinets. Stamped steel construction maintains the geometry of the support over time, which helps preserve the original shelf height settings after repeated removal and resetting during trimming, edge banding, or cleaning. The 0.75 inch length defines how far the shelf can slide back onto the support, giving installers a tactile stop that speeds up placing multiple shelves at the same reveal. The bright brass finish makes each support easy to see inside deeper cabinets, which helps installers verify support positions quickly when adjusting shelf spacing on site. The EPCO brand and 522-B part number identify this specific configuration, which aids in reordering the exact same support when matching an existing job.
Epco 522-B shelf support uses a 5 mm pin, so it fits 5 mm diameter drilled holes and works with standard 5 mm system boring used in many cabinet and closet panels.
The 0.75 inch length gives a defined bearing ledge under the shelf, helping keep shelves seated at a consistent depth relative to cabinet faces and doors.
Epco 522-B shelf support is stamped steel, providing a rigid platform that helps maintain shelf alignment in cabinets bored for 5 mm pins.
The bright brass finish on this shelf support suits cabinet and closet interiors that coordinate with brass-toned hardware and also improves visibility inside darker spaces.
The EPCO 522-B part number designates this stamped steel shelf support with a 5 mm pin, bright brass finish, and 0.75 inch length for consistent reordering.
This Epco 522-B shelf support is sold each, which suits projects where installers need specific counts for individual cabinets or service replacements.
The Epco 522-B shelf support pairs a 5 mm pin with stamped steel construction, so it matches standard 5 mm system boring while giving shelves a solid bearing point. Its 0.75 inch length and bright brass finish support accurate placement and quick visual checks across cabinet runs. Sold each through Wurth Baer Supply, it suits both new installations and matching repairs where the same style must be maintained. For projects built around 5 mm holes and brass-toned hardware, this support offers a consistent, repeatable solution.
Sold In: 1 Each