Epco 841-DC open flange gives you a dedicated mounting point for closet tubing using a simple two-pin design, so you can support a rod securely while keeping installation straightforward on closet or shelving projects.
The flange uses two 32mm mounting pins, creating a fixed layout that aligns with 32mm drilling systems, which matters when you want repeatable hole patterns across closet panels or casework components.
Those pins are spaced 32mm center-to-center, so the flange locks into matching 32mm rows without layout guesswork, helping you position each support in line with your drilling template or line boring pattern.
A dull chrome finish on the flange provides a neutral metal look that blends with typical closet tubing and hardware, which helps your finished runs look consistent when you are matching other dull chrome closet components.
The part is classified under closet rods and flanges, so it is intended to function as a structural support point in a closet tubing run where a rod needs a stable, fixed bracket on a panel or end support.
This open flange uses two 32mm mounting pins to anchor into your panel, so the installation relies on pre-bored 32mm holes instead of loose measuring, which helps keep flange locations consistent from cabinet to cabinet.
The 32mm center-to-center spacing of those pins aligns with common line-boring equipment, which means you can drill your closet sides on a standard pattern and then seat each flange directly into the bored holes.
Positioning the flange by its pins gives you a fixed reference for supporting closet tubing, so once the holes are drilled on the 32mm grid, you can repeat the same rod height and setback across an entire run.
The dull chrome finish on the flange face gives a clean, finished look around the rod seat, which is useful when the mounting area is exposed and you want hardware that visually matches other dull chrome parts.
The Epco 841-DC open flange is used in closet, shelf, and garage organization projects where closet tubing needs a stable support, so it functions as one of the fixed bearing points for a hanging rod run.
Because it sits in the closet rods and flanges class, the part is intended specifically for rod support rather than general brackets, which keeps its role focused on carrying closet tubing load into side panels or end supports.
The two 32mm mounting pins are designed for substrates drilled on a 32mm pattern, so the flange fits naturally into closets or cabinets built around that system, tying rod placement to your existing hole layout.
Using the 32mm center-to-center spacing, you can locate flanges at consistent elevations within tall units, which is useful when stacking multiple rods at defined heights in a wardrobe or multi-bay closet system.
The dull chrome finish fits typical closet tubing finishes, so when you install this flange in visible areas, the hardware appearance aligns with other dull chrome organization components used throughout the project.
The two 32mm mounting pins establish a positive mechanical location for the flange, so it seats into pre-drilled holes and resists shifting, which helps maintain rod alignment over repeated opening, closing, and loading cycles.
With the 32mm center-to-center spacing tied to a standard system, the flange can be placed using line-bored rows instead of hand-marked positions, which reduces layout variation between different panels or cabinets.
That predictable pin layout simplifies planning multi-section closet runs, because the same drilling program that sets shelf pins or hardware rows also positions the flanges that carry the closet tubing.
The dull chrome surface provides a uniform, low-glare metal appearance around the rod contact point, so when doors are open or rods are exposed, the flange visually matches dull chrome rods rather than drawing attention.
Using a defined manufacturer part number, 841-DC, means this same flange design can be specified again on future jobs, which supports consistent hardware selection across multiple installations and simplifies ordering.
Being sold as each allows you to pull the exact count needed for a layout, which helps align material usage with specific closet rod runs without tying the job to preset quantities.
The Epco 841-DC open flange supports closet tubing as part of closet rods and flanges, so it serves as a fixed point that carries the rod load into a panel or support member.
The 32mm mounting pins locate the flange in pre-bored 32mm holes, so it seats in a repeatable position that aligns with standard line-boring patterns on closet or cabinet sides.
On this flange, 32mm center-to-center means the two mounting pins are spaced 32mm apart, which matches common 32mm system drilling and keeps multiple flanges aligned vertically.
The flange has a dull chrome finish, giving it a subdued metallic look that visually coordinates with dull chrome closet tubing and similar closet hardware in the same installation.
This open flange is in the closet rods and flanges product class, meaning it is intended to act as a support point specifically for closet tubing rather than general shelving.
The 841-DC open flange is manufactured by EPCO, so it can be specified and reordered by that brand and part number when matching hardware across projects.
The Epco 841-DC open flange with two 32mm mounting pins gives you a defined support point for closet tubing on 32mm-based projects, so you can tie rod placement directly to your drilled system layout.
Its dull chrome finish and role within closet rods and flanges align with typical closet organization hardware, making this EPCO part a straightforward choice when you want consistent appearance and repeatable mounting.
Sold In: 1 Each