3" Wide x 28" High Square Rockwell Table Leg Set, Brushed Steel, 4/Set

3 Inch Wide 28 Inch Table Leg Set For Stable Work Surfaces

3 inch wide 28 inch table leg set from Peter Meier, Inc. provides a matched group of four 28 inch high Rockwell legs that support a consistent work surface or table height, which helps keep multiple tops level across a run. The square Rockwell table leg set design defines a clear 3 inch wide footprint at each corner, so installers can plan layout and clearances around the leg envelope during project planning. The table legs sit at a fixed 28 inch nominal height, giving a standard base height that suits many work surface and table builds where a seated working position is needed. The set format groups all four supports under one part number, which streamlines ordering and matching for repeat installations that use the same Rockwell style leg.

Rockwell Table Leg Set Details That Support Builds

• The Peter Meier, Inc. Rockwell table leg set in brushed steel presents a consistent finish across all four legs, which helps projects keep a uniform look when multiple legs are visible on open tables or work surfaces.
• The 3 inch wide square design provides a defined, robust leg profile, which helps distribute load into the floor contact area and supports stable corner or mid-span support locations under a variety of top sizes.
• The 28 inch high table legs establish a fixed working height for table and work surface projects, which simplifies planning when matching new surfaces to existing seating or adjacent casework.
• The set of four legs and screws br format ties all four supports to one specification, which supports repeatable layout and reduces variation between legs on the same installation.
• The 4 9/16 inch, or 116 mm, square mounting plate integrated with each leg provides a broad interface to the underside of the top, which spreads forces over a wider area of the substrate.
• The 1 1/8 inch adjustable foot range on each leg gives vertical fine-tuning, which helps compensate for uneven floors and brings the finished top into plane with surrounding surfaces.

Mounting And Adjustment For Rockwell Table Leg Set

The Rockwell table leg set uses a 4 9/16 inch, or 116 mm, square mounting plate, which gives installers a predictable layout for screw locations on the underside of the top. The 3 inch wide square leg profile meets this plate, creating a clear transition between leg and top interface, which assists in aligning edges parallel to the table perimeter. Each 28 inch high leg incorporates a 1 1/8 inch adjustable foot, which provides a useful vertical adjustment window to correct for floor variation without altering the relationship between the mounting plate and the work surface.

Using Peter Meier Rockwell Legs In Real Projects

Where These 28 Inch Rockwell Legs Are Applied

The Rockwell leg 4 piece set at 28 inch height is suited to work surface and table projects that fall within the Work Surface & Tables category, which positions it firmly in shop, office, or residential table builds using that standard height. The 3 inch square leg shape helps when fitting under rectangular tops, because the consistent cross-section allows the installer to place legs close to corners without unexpected protrusions. The brushed steel finish on the Peter Meier, Inc. Rockwell table leg set presents a contemporary metal look, which aligns well with laminate or wood tops where a metal support is desired alongside those materials. The 4 9/16 inch square mounting plate dimension fits typical underside clearances on many tops, so installers can position the plate to avoid edge banding or hardware zones while still capturing a broad screw pattern.

Why Mounting Details And Adjustment Improve Results

The 4 9/16 inch, or 116 mm, square mounting plate on each leg offers multiple fastener positions across both directions, which can reduce localized stress by sharing loads across a wider underside area of the work surface. The 1 1/8 inch adjustable foot range helps the installer address floor slopes or irregularities, allowing the finished table or work surface to be leveled while keeping the mounting plates tightly seated against the underside of the top. The defined 28 inch leg height works in combination with the adjustable foot to maintain a predictable finished height zone, which is useful when tying a new surface into adjacent casework or other tables in the same space. Using the Peter Meier 876-28-ST Rockwell table leg set with these mounting and adjustment features supports consistent results from one installation to the next, which benefits projects that repeat the same table design across multiple rooms or locations.

Common Questions About 3 Inch Wide Rockwell Legs

Selecting This Rockwell Table Leg Set For Your Build

The Peter Meier, Inc. 3 inch wide 28 inch table leg set with brushed steel finish, 4 9/16 inch square mounting plate, and 1 1/8 inch adjustable foot offers defined dimensions that translate directly into layout and leveling on site. When a project calls for table or work surface legs that align with the Work Surface & Tables category, the Rockwell leg 4 piece set, manufacturer part 876-28-ST, gives a single specification that ties together height, footprint, and adjustment. Use this Rockwell table leg set when a consistent 28 inch leg height, square 3 inch profile, and adjustable foot are a good match for the tables or work surfaces being built.