Domi Snap-On 1-Cam Mounting Plate gives cabinet builders a hinge base designed for Salice hinges Series F and Series B, so one plate style can serve multiple hinge lines when laying out doors across a project or shop run. This mounting plate uses wood screws, which lets installers fasten directly into cabinet cases or frames using common drilling patterns. The plate has a 0mm height, so the hinge arm starts flush at the mounting surface, helping establish a known reference line for consistent reveal planning across a bank of doors. Nickel-plated construction resists corrosion, which supports long-term hinge performance in typical kitchen and bath environments. The economical clip-on design lets the hinge clip onto the plate, so doors can be removed or adjusted at the plate without disturbing the screw pattern.
This Salice hinge mounting plate is designed as an economical clip-on style, so the hinge arm attaches to the plate rather than directly to the cabinet, which speeds both initial hanging and later removal. The 0mm plate height establishes a neutral starting position, useful when following Salice drilling charts or standard overlay calculations. Depth adjustment from -0.5 mm to +2.8 mm is handled by an eccentric cam, giving smooth, repeatable fine-tuning of door projection relative to the cabinet front. The plus or minus 2 mm height adjustment uses slotted holes, so the plate can be shifted up or down slightly after the screws are set, allowing installers to level doors across adjoining cabinets without altering the hinge arm.
This hinge mounting plate works with all Salice hinges Series F and Series B, so it suits frameless or face-frame cabinet programs built around those hinge families. The standard 37 mm x 32 mm positioning matches common system boring dimensions, which helps align with established drilling templates on case sides or rails. The 0mm plate height keeps the hinge arm close to the cabinet surface, which is useful when following overlay charts that assume a flat base plate. Because the plate attaches with wood screws, it is suited to solid wood or engineered wood cabinet construction where direct screw mounting is preferred for strength and serviceability. The economical clip-on design ties into Salice hinge clips, supporting projects that need repeat adjustments over time.
The eccentric cam depth adjustment from -0.5 mm to +2.8 mm lets installers shift the door closer to or farther from the cabinet, which helps correct minor drilling offsets and achieve even reveals at the front. Height adjustment of plus or minus 2 mm through the slotted holes allows doors to be raised or lowered slightly without changing the hinge arm setting, which is important when leveling multiple doors across a wide cabinet or tall pantry. Using the standard 37 mm x 32 mm positioning, shops can run boring operations in a consistent pattern, then depend on the mounting plate adjustments to handle small variations, reducing rework. The nickel-plated, corrosion-resistant finish helps the adjustment mechanisms operate smoothly over time in typical kitchen, bath, or storage environments. Together, these features support accurate alignment with minimal effort on site or in the shop.
The Domi Snap-On 1-Cam Mounting Plate is compatible with all Salice hinges Series F and Series B, allowing one plate style to support both hinge families on a project.
The mounting plate offers depth adjustment from -0.5 mm to +2.8 mm by eccentric cam, so door overlay can be fine-tuned without altering drilling positions.
The plate provides height adjustment of plus or minus 2 mm through slotted holes, helping align door tops and bottoms after installation.
The 0mm height means the hinge arm sits at the cabinet surface level, which supports overlay layouts that assume a flat base plate reference.
The standard 37 mm x 32 mm positioning matches common system boring patterns, allowing consistent drilling setups across cabinets and jobs.
The nickel-plated, corrosion-resistant finish protects the plate in typical kitchen or bath conditions, supporting long-term hinge function and adjustment.
The Domi Snap-On 1-Cam Mounting Plate with wood screws, 0mm height, and standard 37 mm x 32 mm positioning gives a straightforward base for Salice Series F and Series B hinges. Depth adjustment by eccentric cam and plus or minus 2 mm height adjustment provide enough range to fine-tune overlay and alignment without reboring cases. Nickel-plated, corrosion-resistant construction and a lifetime warranty from Salice America support long service in cabinet applications. For projects built around Salice hinges, this economical clip-on plate offers a practical, repeatable way to hang and adjust doors.
Sold In: 300 Each