Kensington Maple edgebanding gives a defined Kensington Maple edge to panels where the core would otherwise be exposed, so cabinet and furniture projects present a consistent finished appearance around every visible side. This PVC edge banding is 2mm thick, so it adds a solid, substantial edge profile that stands up to normal shop handling and everyday use in typical woodworking environments. The 7/8 inch width works with standard 3/4 inch panels while providing extra coverage for trimming, so installers can achieve a flush, tight edge line. With a 300 FT length, this roll supports multiple cabinets or larger runs in one color, which helps maintain visual continuity across a project. The product is supplied by Rehau, Inc. as edge banding in the Edgebanding & Surfacing category, so it is suited to professional shop workflows where consistent edging is required.
This Kensington Maple edgebanding is specified at 7/8 inch width and 2mm thickness, so it pairs well with standard 3/4 inch panel builds that require a heavier edge profile. The 7/8 inch width gives working room beyond the panel face, so edge-banding equipment can apply and then trim the overhang down to a clean line. The 2mm thickness provides a noticeable edge radius once trimmed, so finished components feel solid at the touch points. Because the product is a 300 FT roll of PVC edge banding, it can be run repeatedly through edgebanding machines in a single setup when a project uses the Kensington Maple look throughout.
The designation Kensington Maple Edgebanding 2mm Thick, 7/8 inch Width x 300 FT identifies this product as edge banding intended for covering exposed edges on panels and similar components. In cabinet shops and woodworking environments, the Kensington Maple tone can be selected where a Kensington Maple face material is used, so the edge line visually supports the chosen surface design. The 7/8 inch width is suited to edging around doors, drawer fronts, and casework constructed from 3/4 inch stock, because it leaves a controllable amount of overhang for machining. With the product classified under Edgebanding & Surfacing as edge banding, it fits into operations where edging is applied as a standard step in panel processing. The 300 FT length per roll supports multiple cabinets or a full room set that uses the same Kensington Maple finish. That length also helps maintain color continuity within a job, because the entire run can draw from a single, consistent edgebanding source rather than multiple short lengths.
The combination of 2mm thickness and 7/8 inch width in this Kensington Maple PVC edge banding directly affects how the finished edge performs and looks. The 2mm thickness creates a substantial edge that, once trimmed, presents a firm feel where doors and drawer fronts are handled, which is valuable around high-touch cabinet areas. This thickness also supports a more defined profile after trimming, so the transition from face to edge appears deliberate instead of minimal. The 7/8 inch width gives additional coverage over 3/4 inch panels, allowing trimming equipment to remove material cleanly without risking a thin or starved edge. Across a 300 FT roll, those dimensions allow production crews to run repeated passes with the same setup, maintaining consistent edge appearance and feel from one part to the next. Because the material is PVC edge banding from Rehau, Inc., it is aligned with common edgebanding processes used in woodworking shops.
The Kensington Maple edgebanding is specified at 7/8 inch width and 2mm thickness, so it suits edging applications on standard 3/4 inch panels with extra width available for trimming operations.
The Kensington Maple PVC edge banding roll is 300 FT long, so it supports edging multiple cabinets or larger panel runs in the same color within a single project setup.
The Kensington Maple edgebanding is PVC edge banding, which integrates with common edgebanding equipment in woodworking shops that are set up to process PVC materials.
This Kensington Maple PVC edge banding is supplied by Rehau, Inc., giving shops a defined manufacturer source and part reference for repeat projects.
The part number 301683-001 identifies this specific Kensington Maple Edgebanding 2mm Thick, 7/8 inch Width x 300 FT from Rehau, Inc. for ordering and reordering.
The 2mm thickness of this Kensington Maple edgebanding creates a more substantial edge profile, which provides a firmer feel and defined transition between panel face and edge on completed components.
Kensington Maple edgebanding 2mm Thick, 7/8 inch Width x 300 FT provides a defined Kensington Maple edge solution for panel work that uses this finish. The 7/8 inch width and 2mm thickness support edging on 3/4 inch material with a solid profile, while the 300 FT length helps carry that look across multiple cabinets or full room sets. For jobs that specify Kensington Maple surfaces, this PVC edge banding from Rehau, Inc. gives a consistent edging component with a clear part reference in 301683-001.
Sold In: 1 Roll