Senco 23 gauge micro pin gives installers a slim fastener that secures the smallest trim while keeping surface damage minimal. The 23 gauge size keeps the pin thin, so it fastens delicate material while reducing the visual impact. The 5/8 inch length works for light trim applications where holding power is needed without driving through thin stock. The headless design lets the pin sit flush in the wood, which keeps the hole nearly invisible and reduces the need for surface repair. As a pin head nail in the brad nail family, it fits workflows where a light fastening point is preferred over larger brads. The galvanized finish on each pin adds a protective coating, which helps the fastener perform in typical woodworking environments. The Senco CZ10EAAR part number identifies this specific combination of 23 gauge, 5/8 inch length, headless style, and galvanized finish for repeat ordering.
This Senco 23 gauge x 5/8 inch micro pin is designed for work where visible fasteners would disrupt the finished surface. The slim 23 gauge profile allows the pin to penetrate small trim pieces, which supports clean attachment on narrow moldings. The 5/8 inch length is suited to fastening situations where the material stack is thin, so the pin anchors the piece without excessive projection beyond the back. The headless style leaves only a small entry point, which keeps the hole nearly invisible on painted or stained trim. As a galvanized finish pin, it brings a coated surface to the fastening point, which supports typical indoor woodworking conditions found in trim and cabinetry shops.
The Senco CZ10EAAR 23 gauge x 5/8 inch micro pin works where delicate trim needs to be held in place without distracting marks. Its position in the pin head nails class within the brad nails category aligns it with detailed fastening tasks on small profiles. The 23 gauge wire size keeps the fastener narrow, which suits operations on fine trim, small returns, or detail strips where a heavier brad could mark the edge. With a 5/8 inch length, the pin fits applications that rely on shorter penetration, such as attaching thin trims to a substrate in cabinetry or interior woodworking. The headless design supports situations where the finish surface is visible, because the pin does not leave a pronounced head impression.
The headless configuration of this Senco 23 gauge micro pin lets the fastener sink into the material, which leaves a small entry that is nearly invisible in the field. This characteristic is valuable during trim and finish work, because the surface shows fewer fastener marks after fastening. The galvanized finish on the pin provides a coated exterior, which supports the fastener surface as it sits in typical interior woodworking environments. Being part of the Senco Products, Inc. lineup gives the micro pin a defined manufacturer part number, CZ10EAAR, which simplifies selection when the same gauge, length, and finish are desired again. Together, the 23 gauge size, 5/8 inch length, headless style, and galvanized finish provide a combination aimed at light trim fastening where appearance of the surface matters.
The Senco CZ10EAAR is a 23 gauge x 5/8 inch micro pin classified as pin head nails in the brad nails category, so it serves light trim and detail fastening tasks.
The 23 gauge size makes the micro pin very slim, so it penetrates small or delicate trim pieces while reducing the chance of visible edge damage on the workpiece.
The 5/8 inch length suits thinner trim assemblies, providing holding power for light fastening where only shallow penetration is required into the substrate.
The headless design lets the Senco 23 gauge micro pin sit flush in the material, which leaves a nearly invisible hole and helps preserve the finished trim appearance.
The galvanized finish adds a protective coating to the micro pins, which supports the fastener surface in typical cabinet and trim woodworking environments.
The CZ10EAAR part number identifies Senco 23 gauge x 5/8 inch galvanized headless micro pins, which helps match the same fastener specification for repeat trim projects.
The Senco 23 gauge x 5/8 inch micro pin delivers a thin, headless fastener for trim where surface appearance is important. Its role as a pin head nail within the brad nails category positions it for light, detailed fastening work. The galvanized finish supports the fastener surface in standard interior woodworking conditions. For projects built around the same gauge, length, and low-visibility fastening, the Senco CZ10EAAR part number provides a consistent option for repeat trim and finish tasks.
Sold In: 1 Box