Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Federal Brace NOMARR cover cap is a red PVC peel and stick surface protection piece designed to guard finished surfaces from scratches, scrapes, and marring caused by tools while driving fasteners during installation and assembly, which helps maintain a consistent finished appearance across your project. The NOMARR non-marring surface protection uses patent pending technology to shield the area around the fastener head during installation, so tool contact is absorbed by the cap instead of the work surface. Its role as a screw cover cap within the screw cover caps and washers category ties directly into fastener-driven assemblies where finish quality is important. The inexpensive and easy to use design supports fast-paced installation workflows by adding protection in one quick step, which supports a cleaner result without revisiting damaged spots.
The NOMARR surface protection cap has dimensions of 1.63 inches by 1.13 inches by 0.13 inches, giving a defined coverage area around each fastener so the working zone for the driving tool is shielded during tightening. It is designed for shaft diameters from 3/8 inch to 7/16 inch, meaning it fits around fasteners in that size range where drivers commonly contact nearby surfaces. The cap also matches socket diameters from 9/16 inch to 5/8 inch, aligning the protective zone with typical socket tool sizes used on those shafts, so the tool operates inside the protected footprint instead of against the finished surface.
This NOMARR non-marring surface protection is designed to sit around fasteners where tools drive screws or bolts during installation and assembly, so the finished material directly surrounding the fastener head is covered. With its 1.63 inch by 1.13 inch footprint, the cap creates a defined buffer zone large enough for sockets in the 9/16 inch to 5/8 inch range to operate without contacting the adjacent surface, which is useful when working close to visible edges or finished faces. The 0.13 inch thickness gives the protection enough body to separate tool faces from the work surface while remaining low profile relative to surrounding materials, so installation can proceed without significantly altering how the driver engages the fastener. Because it fits shaft diameters from 3/8 inch to 7/16 inch, the cap is suited to common mid-range fasteners where high torque or repeated driver contact would otherwise risk scuffing the finish at each connection point. In assembly settings using multiple similar fasteners, the red color identifies each protected location at a glance, so installers can move quickly from point to point while keeping the same level of surface care.
The peel and stick design lets the Federal Brace NOMARR cover cap be positioned around the fastener area before driving tools are applied, so the installer sets the protection exactly where sockets sized from 9/16 inch to 5/8 inch will operate. Once in place over a shaft in the 3/8 inch to 7/16 inch range, the PVC body absorbs incidental contact from the driving tool as torque is applied, keeping the underlying substrate free of the scratches, scrapes, and marring typically caused during fastening. The inexpensive construction supports using a cap at every visible fastener location, which helps deliver a consistent finished look across the entire run without leaving some spots unprotected. As part of the screw cover caps and washers category, this NOMARR component is intended to work in the same workflow as the fasteners themselves, so surface protection becomes a standard part of installation and assembly rather than a separate repair step afterward, helping maintain attention to detail on each completed project.
The NOMARR cover cap protects finished surfaces around fasteners from scratches, scrapes, and marring caused by tools driving fasteners, which helps preserve the visible appearance in assembled work.
The NOMARR surface protection fits shaft diameters from 3/8 inch to 7/16 inch, so it works with fasteners in that size range where driver tools operate close to the finished surface.
The NOMARR cover cap is sized for socket diameters from 9/16 inch to 5/8 inch, positioning the protective area so these sockets drive fasteners without scraping the surrounding surface.
The peel and stick design allows the cap to be set in place over the fastener area before driving, placing the protection exactly where the tool will contact and supporting consistent coverage.
The NOMARR cover cap measures 1.63 inches by 1.13 inches by 0.13 inches, defining a protective footprint sized to shield the immediate tool working zone around the fastener.
This Federal Brace NOMARR part is classified as a screw cover cap and washer component, so it works directly with fasteners to add non-marring surface protection at each connection.
The Federal Brace NOMARR red PVC peel and stick cover cap, FB-03197, provides non-marring surface protection around fasteners during installation and assembly, using its 1.63 inch by 1.13 inch by 0.13 inch footprint to shield finished surfaces where tools contact. With sizing for 3/8 inch to 7/16 inch shafts and 9/16 inch to 5/8 inch socket diameters, it ties protection directly to common fastener and tool combinations, supporting clean, consistent finishes across visible connection points.
