Salice Self-Close Half Overlay Face-Frame;Frameless Hinges Titanium, 94° Screw-On - CNA7G66

Salice Self-Close Half Overlay Hinge For Thicker Doors

Salice self-close half overlay hinge gives cabinet doors a controlled close and half overlay coverage, so doors align to face-frame or frameless cabinets while reducing door slamming in everyday use. As a concealed cabinet hinge in the Salice Series N line, it sits hidden inside the cabinet, keeping the exterior clean while still allowing full hinge function on profile and thicker doors. The 94 degree opening angle lets the door swing wide enough for access while maintaining door control in tight spaces or near adjacent doors. A 12 mm deep cup is bored into the door, providing a stable seating depth that suits many thicker door constructions. This hinge is part of Salice Series N for profile and thicker doors, so it supports door designs where a standard thin-door hinge would not give proper geometry.

Key Working Details For Cabinet Hinge Selection

• Salice Series N design works on profile and thicker doors, helping installations where raised profiles or added door thickness change the hinge geometry compared with standard doors.
• The half overlay configuration positions the door to cover only part of the cabinet side or face frame, giving spacing for adjacent doors and consistent reveals across a run of cabinets.
• The self-close function pulls the door shut at the end of travel, which helps doors stay closed without separate catches and reduces the need for repeated alignment checks during normal use.
• A 94 degree opening angle lets the door open wide enough for cabinet access while keeping the swing controlled, useful when cabinets are set near walls or other doors that limit full opening.
• The 12 mm deep cup bored into the door offers a defined mounting depth that supports thicker doors, maintaining hinge strength and alignment over the life of the installation.
• Compatibility with all traditional Series 200 mounting plates and Domi snap-on mounting plates gives flexibility to match existing plate styles and mounting positions on cabinet carcasses.

Hinge Mounting, Cup Boring, And Plate Interface

This Salice self-close half overlay hinge uses a screw-on mounting style, so the hinge arm attaches to the cabinet and door using screws through the hinge flanges, providing a solid mechanical connection suited to woodworking substrates. The hinge cup is 12 mm deep and is bored into the door, so the installer drills a consistent cup recess that locates the hinge precisely in the door thickness. Possible drilling distance on the door, identified as the K dimension, ranges from 3 to 14 mm, giving a wide adjustment window to set overlay and reveal for various cabinet layouts. Because this hinge is compatible with all traditional Series 200 mounting plates and all Domi snap-on mounting plates, it integrates into existing Salice plate systems where those plates are already positioned on cabinets. The 94 degree opening angle and half overlay configuration then work together to set clearances between doors and frames.

Using This Salice Series N Hinge In Real Projects

Where This Half Overlay Hinge Performs Best

This Salice self-close half overlay hinge from Series N works on profile and thicker cabinet doors, so it fits projects where door thickness exceeds standard ranges or where a shaped door edge changes hinge seating. In those situations, the hinge geometry is tuned for thicker doors, helping the door close flush to the cabinet while maintaining the intended reveal. The half overlay design positions the door so it only partially covers the side or face frame, allowing two doors on a shared partition without binding. On both face-frame and frameless cabinets, this half overlay layout supports consistent spacing between doors across a run. The 94 degree self close hinge motion provides enough swing for reaching into the cabinet while limiting travel, which is useful on corner cabinets or runs that end near walls, preventing the door edge from striking adjacent surfaces.

Details That Support Adjustment And Repeatable Results

The possible drilling distance on the door, with a K range from 3 to 14 mm, lets the installer choose boring positions that fine-tune overlay and door gap across different cabinet configurations. By working within that K range, the same Salice Series N hinge can adapt from small overlays on face frames to larger overlays on frameless cabinets while keeping door alignment predictable. The 12 mm deep hinge cup sets a stable reference inside the door, which supports repeated cup boring operations on multiple doors so they hang level to one another. Compatibility with all traditional Series 200 mounting plates means existing layouts that already use those plates can accept this CNA7G66 Salice hinge without relocating plates, preserving prior drilling work. When Domi snap-on mounting plates are used, the hinge connection to the plate follows that system, supporting quick mounting and removal while preserving the plate position. Across a job, these combined details reduce rework by letting installers repeat the same boring depths, K dimensions, and plate positions from cabinet to cabinet.

Common Questions About This Salice Cabinet Hinge

Selecting The CNA7G66 Hinge For Your Cabinets

The CNA7G66 Salice hinge pairs a 94 degree self close hinge action with half overlay geometry, so it suits cabinet runs that need controlled opening and shared partitions between doors. By using the 12 mm cup depth and the 3 to 14 mm K drilling range, installers can align multiple thicker or profile doors to the same reveal standard across a project. Compatibility with Salice Series 200 and Domi snap-on mounting plates means this hinge fits established Salice plate layouts on both face-frame and frameless cabinets. For work that calls for a concealed cabinet hinge tuned to thicker doors with half overlay, this Salice Series N model offers a focused option.