
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
EPCO GP Series stick-on pull is a 2-13/16 inch long plastic sliding door pull that creates a low-profile grip area on doors where a recessed handle is not desired. The flush pull, stick-on design sets this part up for surface mounting instead of routing or mortising, which helps keep installation focused on layout rather than cutting. The 1/8 inch projection keeps the handle close to the door face, which reduces interference with adjacent doors or frames in tight installations. The 13/16 inch width provides a defined finger area along the edge of a sliding or bypass panel, which supports consistent operation in repeated daily use. The black finish visually blends with darker door surfaces, which helps the hardware sit back while still remaining functional. The GP17-B manufacturer part number clearly ties this pull to the EPCO GP Series family, which supports accurate product selection across multiple openings.
The flush pull, stick-on construction means this handle is installed directly on the door surface, which shifts preparation toward cleaning and aligning rather than machining. The 2-13/16 inch length simplifies layout because it is short enough to fit typical stile areas while still providing a defined pull point. With only 1/8 inch projection from the door face, the pull keeps clearance demands low, which matters when doors slide in front of casework, into pockets, or past adjacent panels. The 13/16 inch width concentrates the grip where it is needed, which helps the installer position the pull consistently at hand height across several doors.
The flush pull, stick-on description positions this GP17-B pull for sliding or similar doors where a shallow, surface-mounted grip is needed. The 2-13/16 inch length suits narrow stiles often found on sliding or bypass cabinet doors, which helps keep the pull centered without overhanging edges. With 1/8 inch projection, the handle stays close to the door face, which supports applications where panels pass close together or track clearances are tight. The 13/16 inch width creates a defined area that fingers can reliably catch, which helps users control smaller or lighter doors with a single hand. The plastic material supports use on interior woodworking projects where moderate contact occurs, which fits typical cabinet or light sliding door applications. The black finish supports doors that use dark laminates or painted surfaces, which helps the pull integrate into commercial or residential casework schemes without drawing extra attention.
The 2-13/16 inch length and 13/16 inch width work together to create a repeatable footprint, which helps installers align multiple pulls at the same offset from edges for a uniform look across a run of doors. The 1/8 inch projection affects how close sliding doors can travel past frames and adjacent panels, which supports layouts where clearances are minimal and protruding hardware would interfere. The plastic construction maintains a consistent profile from pull to pull, which matters when projects use several identical pieces across a bank of cabinets or sliding faces. The flush pull, stick-on design eliminates the need for routed pockets, which preserves door strength and surface treatments on thinner materials. The GP17-B manufacturer part number anchors this pull within EPCOs GP Series, which helps match additional pulls on future openings to the original selection. The black finish holds a stable, dark appearance, which supports long-term visual consistency in high-visibility installations.
The GP17-B flush pull, stick-on design is suited to sliding or similar doors that benefit from a surface-mounted grip where routing or deeper hardware projection is not desired.
The GP17-B pull length is 2-13/16 inches, the width is 13/16 inch, and the projection is 1/8 inch, which creates a compact, low-profile grip area on the door surface.
The GP17-B pull projects 1/8 inch from the surface, which keeps the profile very low and helps sliding doors pass close to frames or adjacent panels.
The GP17-B is made from plastic with a black finish, which supports a neutral, dark appearance that pairs well with darker cabinet or door surfaces.
The flush pull, stick-on construction focuses installation on surface adhesion and accurate placement, which avoids drilling or routing operations in the door panel.
The GP17-B manufacturer part number identifies this specific EPCO GP Series flush pull, which helps match the same size, material, and black finish across multiple doors.
The EPCO GP Series stick-on pull pairs a 2-13/16 inch length with 13/16 inch width and 1/8 inch projection, which supports tight, repeatable layouts on sliding or cabinet doors. The plastic construction and black finish create a consistent, low-profile grip area that lines up reliably across multiple openings. The flush pull, stick-on mounting focuses work on positioning and adhesion, which suits projects that prioritize clean surfaces over machined recesses. For jobs that call for a compact, black stick-on flush pull with defined dimensions, the GP17-B part offers a clear, repeatable choice.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each | EPGP15B Mfr# GP15-B | EPCO GP 2-3/4" (70 mm) Length Satin Brass Stick-On Pull, GP15-B | ||||
Sold in: 1 Each | EPGP15BL Mfr# GP15-BL | EPCO GP 2-3/4" (70 mm) Length Satin Black Stick-On Pull, GP15-BL | ||||
Sold in: 1 Each | EPGP17BLK Mfr# GP17-BL | EPCO GP 2-13/16" (71 mm) Length Black Stick-On Pull, GP17-BL | ||||
Sold in: 1 Each | EPGP17C Mfr# GP17-C | EPCO GP 2-13/16" (71 mm) Length Clear Stick-On Pull, GP17-C |