Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Black bumper edge moulding from Patwin Plastics is a specially formulated flexible PVC "rubbery" plastic that stays flexible instead of becoming brittle, so it holds up in service where edges see bumps and abuse. This bumper edge moulding is designed to seat firmly, which means it grips the edge securely once driven into a 1/8 inch kerf. The moulding is designed to hug the edge permanently, so the trim continues to protect workpiece edges over time without relaxing away from the surface. The self-healing effect when subject to abuse lets the material recover after minor impacts, helping the edge maintain a consistent look and contact line. The 1-1/4 inch width provides coverage across the edge area, giving more surface protection along the edge profile. The Patwin Plastics, Inc. bumper edge moulding is supplied as a 250 ft length, so longer runs and multiple pieces can be edged from a single roll during shop production.
This bumper edge moulding is sized for a 1/8 inch kerf, giving a clear target for the saw or cutter setting so the barbed section can seat firmly along the full run. The flexible PVC "rubbery" construction works with the 1-1/4 inch width to wrap the edge, letting the material conform while maintaining contact along corners and transitions. The design that hugs the edge permanently supports a single-pass installation workflow, with the barbed section holding position once pressed into the kerf. When a radius or curve is too small, the ability to simply notch the barbed section lets the installer adapt the strip on the bench, so tight inside curves can be handled without changing the main edge profile.
This Patwin Plastics, Inc. bumper edge moulding is part of the bumper edge mouldings product class, so it is intended for edges that see contact and abuse in regular use. The specially formulated flexible PVC "rubbery" plastic lets the moulding absorb knocks without becoming brittle, which is important wherever exposed edges may be bumped or scraped. The 1-1/4 inch width gives extended coverage over the edge, which supports using this moulding on thicker workpieces where a narrow trim would expose more surface. Because the moulding is designed to seat firmly and hug the edge permanently, it suits installations where the edge protection is expected to stay in place over long runs. The 250 ft length supports shop situations where multiple panels or components use the same edge detail, allowing repeated cuts from the same continuous strip during production.
The self-healing effect when subject to abuse means the flexible PVC "rubbery" bumper can recover after minor marks, which helps limit visible damage and reduces the need to replace edge protection after incidental impacts. The design that seats firmly and hugs the edge permanently keeps the trim from loosening along the kerf, which reduces callbacks or shop rework to push edging back into place. The 1/8 inch kerf requirement defines the cut for the barbed section, letting installers standardize tooling for consistent fit and grip along repeated parts. When a radius or curve is too small, the ability to simply notch the barbed section lets the installer relieve the back of the moulding so it tracks the curve while the visible face stays even, helping maintain a continuous edge line on tight arcs. The 250 ft length per roll lets shops run long edges or multiple identical pieces from a single setup, supporting efficient, repeatable workflows across projects.
This bumper edge moulding is made from specially formulated flexible PVC "rubbery" plastic, so it will not become brittle and can handle edge abuse in typical use environments.
The bumper moulding is designed for a 1/8 inch kerf, so a slot of that width lets the barbed section seat firmly and grip the edge for a permanent hug along the run.
The self-healing effect lets the flexible PVC bumper recover after minor abuse, so small impacts leave the edge looking more consistent over time.
When a radius or curve is too small, the barbed section can be notched, allowing the moulding to follow tighter curves while keeping a firm fit on the edge.
The 1-1/4 inch width provides broader coverage over the edge area, giving additional protection across the edge profile on thicker components.
The 250 ft roll length supports long continuous runs and multiple parts from one roll, which suits production work using the same bumper edge detail.
The flexible PVC "rubbery" construction of this Patwin Plastics bumper edge moulding will not become brittle, providing durable edge protection where contact and abuse are expected. The design that seats firmly and hugs the edge permanently supports long runs that keep their position during service. With a 1-1/4 inch width sized for a 1/8 inch kerf, the moulding gives defined coverage and a clear cutting target for installation. The self-healing effect under abuse helps the edge maintain a more uniform appearance over time. For projects using bumper edge mouldings from Wurth Baer Supply, this black bumper moulding P575-1-1/4-260 offers a defined material, size, and roll length for planning shop work.
Sold In: 250 Lineal Ft