Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
The Kreg #6 x 1-inch face frame and pocket-hole screw is a fine-thread fastener built for joining hardwood face frame members where splitting, stripping, and rough seating are constant concerns. The 1-inch length is the go-to choice when connecting parts cut from 3/4-inch stock at angles typical of pocket-hole joinery.
At 1 inch, this screw is sized for the most common face-frame joint: rail to stile in 3/4-inch hardwood stock. When the pocket is cut at the standard 15-degree angle into 3/4-inch material, a 1-inch screw reaches through the angled bore and into the mating piece without breaking through the face. It is also the right call when attaching a face frame to a cabinet box where the combined material is thin enough that a longer screw would over-penetrate. Cabinet shops building standard face-frame doors, drawer openings, and stile-to-rail assemblies in maple, oak, and cherry will reach for this length repeatedly.
Fine thread is the correct choice for hardwood. Coarse thread in dense species like maple tends to strip the pocket or require excessive torque to seat, especially when driving repeatedly in a production run. The fine thread form cuts cleanly, holds firmly, and does not over-stress the narrow walls of a pocket-hole bore in 3/4-inch hardwood stock. The modified pan head complements the thread by bearing flat against the pocket wall rather than acting like a wedge. A wedging head — common on bugle-style screws — splits the grain near the pocket opening; the pan geometry distributes the clamping load instead, pulling the joint closed without cracking the stile. The Type 17 Auger point contributes a longitudinal flute that clears wood fibers ahead of the thread, so the screw starts without deflecting and drives with less resistance than a plain sharp point in the same material.
This screw is aimed at shops and installers who build or hang hardwood face-frame cabinetry on a regular basis. The 1200-piece box quantity is a production pack — it is not sized for the homeowner doing a single kitchen. For a shop running maple or oak face frames across a full cabinet order, the box provides enough fasteners to complete an entire project without counting screws. The square drive works well in the restricted swing of a cabinet interior where bit tip-out is more likely than it would be in open framing; a correctly sized #2 square bit seats positively in the recess and transfers torque without the cam-out risk of a Phillips in the same tight position. This screw is for indoor cabinetry only — the zinc finish is not rated for exterior exposure or high-humidity environments.
Fine thread is designed for hardwood species like maple, oak, and cherry. Coarse thread in dense hardwood can strip the pocket bore or require excessive torque to fully seat. Fine thread cuts cleanly and holds firmly without over-stressing the material around the pocket opening.
Yes. When a pocket is cut at the standard 15-degree angle into 3/4-inch stock, a 1-inch screw reaches through the bore and into the mating piece without breaking through the face. It is the standard length for rail-to-stile joints in 3/4-inch hardwood face-frame work.
The modified pan head bears flat against the pocket wall and distributes clamping load evenly. A countersunk or bugle head tapers like a wedge and can split the grain near the pocket opening, especially in tight-grained hardwood. The pan geometry pulls the joint closed without that wedging force.
It will function, but a coarse-thread pocket-hole screw is the better match for softwood, plywood, and MDF. Fine thread in low-density materials does not develop the same pull-out resistance as coarse thread. If the face frame is pine, poplar, or sheet goods, choose the coarse-thread version sized for your stock thickness.
The screw is compatible with standard pocket-hole jig setups for 3/4-inch stock. The pocket-hole jig brand does not affect compatibility — what matters is that the pocket is cut at the correct angle and depth for this screw length and gauge.
When the job calls for tight, clean face-frame joints in maple, oak, or cherry at 3/4-inch stock thickness, this Kreg 1-inch fine-thread square-drive screw is the correct fastener — and the 1200-piece box keeps the shop moving without interruption.
Sold In: 1 Box