Kitchen Kompact Glenwood wall cabinet in the GW24Y model provides a 24 inch wide, 18 inch high, 12 inch deep wall unit that fits standard upper cabinet layouts, so runs line up cleanly with common kitchen and shop designs. The cabinet uses frames built of solid 3/4 inch oak, maple, or beech, giving the face frame real-wood strength where doors mount and where daily contact stresses the front of the unit. Each rail is kiln-dried, then joined by mortise and tenon and glued, creating a stable front frame that resists movement over time, which supports consistent door alignment. Solid wood hanging strips on the wall cabinet are located at the top and bottom, giving two full-width mounting rails that spread the load when fastening to wall framing. End panels use 3-ply construction with a 1/2 inch thick engineered wood core and hardwood veneers, providing a flat, stable side that holds up in cabinet rows while presenting a hardwood surface at the exterior.
Solid wood hanging strips on this Kitchen Kompact wall cabinet run across the top and bottom, giving two structural mounting zones to work with wall framing during installation. Because these hanging strips are solid wood, fasteners can bite into strong material along the full cabinet width, which helps distribute the cabinet load and the weight of stored items. The 3/4 inch solid wood frames at the front give a sturdy edge for joining this unit to adjacent cabinets, allowing clamps and screws to pull face frames together without crushing. Solid wood corner blocks, glued and power nailed, brace the box so it stays square while positioning on the wall. The 3-ply end panels with engineered wood core and hardwood veneers support a consistent side thickness, which helps align scribe cuts and filler pieces when tying into surrounding finishes.
The Glenwood GW24Y wall cabinet at 24 inches wide, 18 inches high, and 12 inches deep suits upper rows where a shorter wall cabinet is required, such as over appliances or in tighter vertical spaces. Its solid 3/4 inch oak, maple, or beech frame allows it to tie into other Kitchen Kompact cabinets that share the same frame construction approach, so face frames align along the run. The 3-ply end panels with 1/2 inch engineered wood core and hardwood veneers mean the sides present a hardwood face that can sit against adjacent cabinets or exposed ends, giving a consistent appearance across a bank of units. Solid wood toe kicks across the Kitchen Kompact line support coordinated layouts between wall and base cabinets, simplifying planning when this wall unit is part of a full Glenwood installation.
The kiln-dried mortise and tenon frame rails, glued for added strength, keep the face frame rigid, which helps maintain door alignment after installation and during regular use. Solid wood corner blocks that are glued and power nailed tie the box together at critical junctions, so the cabinet resists twisting when fastened to less-than-perfect wall surfaces. Solid wood hanging strips at both the top and bottom supply two strong attachment points, helping installers secure the cabinet level and plumb along its full width. The 3-ply, 1/2 inch engineered wood core end panels with hardwood veneers provide a side that is less prone to warping than single-thickness lumber, which supports tight seams between cabinets and straight alignment with trim and fillers. Together these construction choices support repeatable layout, fastening, and alignment steps from one Glenwood 24Y wall cabinet to the next.
The GW24Y Glenwood wall cabinet measures 24 inches wide, 18 inches high, and 12 inches deep, so it fits common upper cabinet runs and shorter wall sections.
The Kitchen Kompact face frame is built of solid 3/4 inch oak, maple, or beech, providing a hardwood front for hinge mounting and daily door use.
Each frame rail is kiln-dried, joined by mortise and tenon, and glued, creating a stable front frame that holds door alignment across the cabinet width.
The GW24Y uses solid wood hanging strips at the top and bottom, giving strong, full-width mounting rails for fastening to wall framing.
End panels have 3-ply construction with a 1/2 inch engineered wood core and hardwood veneers, offering a stable side with a hardwood outer surface.
Cabinet corners use solid wood corner blocks that are glued and power nailed, bracing the box against racking when loaded or adjusted on the wall.
The GW24Y Kitchen Kompact Glenwood wall cabinet combines 24 inch width, 18 inch height, and 12 inch depth with solid 3/4 inch hardwood frames, kiln-dried mortise and tenon joints, and 3-ply end panels. Solid wood hanging strips at the top and bottom and solid wood corner blocks support a rigid, easy-to-align box that integrates into typical upper cabinet runs. For projects built around Glenwood styling and Kitchen Kompact construction, this cabinet offers a defined size and a clearly specified structure for planning your next installation.
Sold In: 1 Each