wood veneer edgebanding pre-glued ash describes a FormWood wood veneer edge banding designed to finish exposed edges on ash sheet goods and components. The edgebanding is made from wood veneer, so it gives an ash surface a matching edge that visually reads as solid wood, which helps maintain a consistent look across doors, drawer fronts, and carcass parts. The 0.034 inch thickness provides enough material to cover substrate irregularities without feeling bulky, supporting clean trimming and light sanding on typical woodworking equipment. The 7/8 inch width covers common panel thicknesses while leaving a bit of overhang, so edges can be trimmed flush for a precise finish. The 250 foot roll length supports continuous edging runs on multiple cabinets or larger projects, which reduces changeovers during installation. The pre-glued construction means the adhesive layer is already applied to the back of the veneer, so heat can activate the bond in one step during edge application.
The pre-glued design of this wood veneer edgebanding means an adhesive layer is factory-applied to the backside, so heat is used to activate the bond during installation, rather than applying separate adhesive. The 7/8 inch width gives coverage beyond standard panel thickness, so after bonding, the excess can be trimmed flush for a square, professional edge line. The 0.034 inch thick veneer provides material for careful trimming and light sanding after bonding, helping installers dial in smooth transitions between the edge and face surfaces. The continuous 250 foot roll length supports feeding through edge application equipment or working extended manual runs without frequent roll changes, which is helpful when edging multiple ash panels in a single setup.
The Wood Veneer Edgebanding, Pre-Glued, Ash, 0.034 inch Thick 7/8 inch x 250 foot Roll from FormWood serves projects that need ash edges on exposed sheet-good sides. In cabinet shops, the 7/8 inch width matches common carcass and shelving thicknesses, so installers can run this edgebanding along upper cabinets, base cabinets, and tall units while maintaining one standard width. The wood veneer ash face allows the edge to read consistently with ash doors, frames, or panels, which is useful when aligning grain and color relationships across a run of cabinetry. The 250 foot roll gives enough length to process a series of cabinets, drawer parts, and shelving from a single roll, supporting repeatability when batching parts for a full room or series of projects.
The PGASH7/8 designation identifies this specific FormWood ash edgebanding, which helps shops standardize ordering and keep the same veneer appearance across reorders and future work. The 0.034 inch thickness is substantial enough to tolerate routine trimming and touch sanding, which supports consistent edge profiles even when adjusting multiple pieces in a production setting. Because the edgebanding is pre-glued, heat activation provides a direct way to bond the edge, giving installers a predictable bonding step that can be repeated from panel to panel. The 7/8 inch by 250 foot roll size balances a manageable roll width with extended linear coverage, which fits well with typical cabinet and furniture runs where consistent ash edge appearance and workflow efficiency are both priorities.
The Wood Veneer Edgebanding, Pre-Glued, Ash is made from wood veneer, so it provides a real ash surface on exposed edges for visual consistency with ash-faced components.
The edgebanding is 0.034 inch thick, giving enough veneer for trimming and light sanding so finished edges can be shaped cleanly in typical shop processes.
This FormWood ash edgebanding is 7/8 inch wide and supplied in a 250 foot roll, supporting extended edging runs on multiple panels or cabinet projects.
The pre-glued backing has adhesive already applied, so heat activation bonds the edgebanding in one step, simplifying the edge application process during production.
The PGASH7/8 manufacturer part number identifies this specific pre-glued ash wood veneer edgebanding, supporting accurate reordering for consistent edge appearance.
This wood veneer ash edgebanding is used on exposed edges of ash cabinets, furniture, and shelving, so sheet-good edges visually match ash-faced surfaces.
The Wood Veneer Edgebanding, Pre-Glued, Ash, 0.034 inch Thick 7/8 inch x 250 foot Roll from FormWood gives woodworking shops a defined solution for finishing ash edges. The wood veneer ash face helps panels, doors, and carcass parts present a unified appearance, while the 0.034 inch thickness supports practical trimming and sanding during normal shop workflows. The 7/8 inch x 250 foot roll format suits repetitive cabinet and furniture production where consistent edge dimensions and long runs matter. Using the PGASH7/8 part number ties future orders back to the same ash edgebanding, helping projects maintain the same look over time.
Sold In: 1 Roll