Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Wood Veneer Edgebanding Pre-Glued Beech describes this FormWood edge banding that finishes exposed panel edges with a matching wood veneer surface. The pre-glued construction means adhesive is already applied to the back, so the installer only needs to activate it during application, which speeds up edge finishing on jobs. The beech wood veneer face provides a real-wood edge that visually ties in with beech panels or similar tones, helping projects look uniform from face to edge. The 0.034 inch thickness gives a veneer layer sized for typical cabinetry and casework edges, so it blends well while still covering substrate edges. The 7/8 inch width is designed to cover common panel thicknesses with some trim allowance, which helps when aligning to slightly uneven or overhanging faces. Supplied as a 250 foot roll, this edgebanding supports longer runs and multiple pieces on a single job without frequent roll changes.
This FormWood edgebanding is classified as wood veneer edgebanding in the edge banding product class, so it is intended specifically for finishing exposed panel edges. The pre-glued description identifies that adhesive is factory-applied to the back, setting it up for activation during installation, which streamlines edge work compared to separate glue steps. With a 0.034 inch thickness, the veneer layer is sized to sit neatly on common panel edges while still masking the substrate, so trimming and flushing can stay controlled. The 7/8 inch width leaves room on either side of typical panel thicknesses, giving installers space to trim to a precise final edge. Supplied as a 250 foot roll, this format supports batch processing of components where multiple shelves, doors, or sides need the same beech edge treatment in one continuous sequence.
This FormWood wood veneer edgebanding in beech is categorized under edgebanding and surfacing, specifically wood edgebanding, aligning it with cabinetry and woodworking projects that expose panel edges. The beech veneer surface lets this edging visually coordinate with beech-based casework, shelving, or similar wood tones, so fronts and sides present a unified material look. The 7/8 inch width works well along edges of panels sized to typical cabinet dimensions, offering coverage plus trimming allowance along both faces. At 0.034 inch thick, the veneer profile is designed to cover the edge of panels used in cabinetry and similar assemblies without appearing overly heavy, which helps the edge read as an extension of the panel surface. The 250 foot roll length supports multi-piece runs for casework, allowing doors, sides, and shelves to share the same continuous beech edging for visual consistency throughout a project.
The pre-glued construction identified in the web description means adhesive is already applied to the back of the edgebanding, so installation focuses on activating that glue and pressing the edge into place, which supports repeatable results across multiple pieces. Because this product is wood veneer edgebanding, the beech surface is real wood, so it responds visually like wood when viewed alongside beech panels, which helps reduce visible transitions at the edge. The 0.034 inch thickness offers a defined veneer layer that can be trimmed flush, supporting clean corners without a bulky lip. With a 7/8 inch width, installers gain side-to-side tolerance during placement, then trim back to the panel, which can reduce rework from slight misalignment. The 250 foot roll format keeps the material continuous over long stretches, which helps maintain a consistent grain direction and color tone from piece to piece within the same run.
The PGBES7/8 edgeband is a FormWood wood veneer edgebanding in the edge banding product class, so it is designed specifically to finish exposed edges on wood-based panels.
This pre-glued beech edgebanding is 7/8 inch wide, giving coverage across typical panel thicknesses with extra margin for trimming flush after bonding to the edge.
The wood veneer layer is 0.034 inch thick, providing enough material to cover substrate edges while still trimming cleanly for a smooth transition to the panel surface.
The FormWood beech edgebanding roll is 250 feet long, which supports edging multiple cabinet parts or longer runs on the same project without frequent roll changes.
Pre-glued on this wood edgeband means adhesive is factory-applied to the back, so installation involves activating that glue and pressing it to the panel edge in one operation.
The face material of this edgebanding is beech wood veneer, allowing exposed edges to visually coordinate with beech panels or similar wood tones in cabinetry or casework.
This FormWood wood veneer edgebanding, pre-glued in beech, brings a 0.034 inch thick veneer face sized for cabinetry edges together with a 7/8 inch width and 250 foot roll length. For projects using beech tones where exposed panel edges need a real-wood finish, choosing this PGBES7/8 edgebanding from Wurth Baer Supply aligns edge treatment with the rest of the build and supports consistent visual results across multiple components.
Sold In: 1 Roll