FormWood Cherry Wood Veneer Edgebanding 7/8", Pre Glued, Unfinished, 250', PGCHE7/8

Wood Veneer Edgebanding Pre-Glued Cherry For Clean Edges

Wood Veneer Edgebanding Pre-Glued Cherry gives cabinet and furniture edges a cherry wood finish using a real wood veneer construction, so visible edges match surrounding cherry surfaces in a consistent way on finished work.

This edge banding is listed at 0.034 inch thick, which provides a workable veneer layer over panel edges, giving enough material to create a neat profile after trimming without feeling bulky along the edge of the panel.

The 7/8 inch width covers typical panel thicknesses with some margin, allowing slight overhang for flush trimming so installers can bring the edge right to the face without exposing the core material of the board.

The roll length is specified at 250 feet, supporting multiple cabinets or longer production runs from one roll, which can reduce mid-job changeovers and help keep edge color and grain character consistent across a full project.

This cherry edgebanding is described as pre-glued, so adhesive is already applied on the back of the veneer, turning it into a ready-to-activate solution that supports straightforward installation workflows using compatible heating equipment.

Key Cherry Edgebanding Details For Projects

• The wood veneer construction means the edgebanding uses real wood on the face, helping visible cabinet and furniture edges present as cherry rather than exposed composite cores whenever the edge is finished.
• A stated thickness of 0.034 inch offers a manageable veneer profile that can be trimmed and lightly profiled after bonding, supporting a smooth transition from the edge to adjacent surfaces on doors, drawer fronts, and casework.
• The 7/8 inch width works with many common panel thickness standards while leaving a small overhang, letting installers flush-trim both faces so the band aligns cleanly with the panel faces on both sides.
• The 250 foot roll length provides extended linear coverage from a single roll, which supports cabinet shops and serious DIY users completing several pieces or a whole room of casework without frequent roll changes.
• The pre-glued designation indicates adhesive is factory-applied to the back of the veneer, turning the banding into a heat-activated solution that streamlines edge work compared to handling separate glue during application.

Edgebanding Fit, Width, And Bonding Workflow

This FormWood wood veneer edgebanding is identified at 7/8 inch wide, so it covers standard panel edges with overhang for trimming, giving users enough material to align, heat, and then flush-trim back to the panel faces.

The 0.034 inch thickness pairs with this width to create an edge that responds well to trimming tools, allowing the installed band to be cleaned up and detailed without overwhelming the edge profile on doors, tops, or shelves.

The pre-glued backing means adhesive is already on the product, so when activated by heat during installation it bonds directly to the substrate, which helps combine edging and gluing steps into one pass along the panel edge.

Because this roll is defined at 250 feet, the same product can be used across a run of casework or multiple furniture pieces, supporting consistent cherry edging appearance anywhere this edgebanding is applied in the project.

Using Cherry Wood Veneer Edgebanding In Workflows

Where This Pre-Glued Cherry Veneer Performs

This FormWood wood veneer edgebanding in cherry sits in the Edgebanding and Surfacing, Edgebanding, Wood category, placing it among products intended to finish exposed panel edges with a wood veneer surface rather than leaving raw board visible.

The cherry veneer face lets this edgebanding align aesthetically with cherry cabinet doors, panels, or furniture components, so when edges are treated, the cherry tone and grain character on corners and openings better relate to adjacent faces.

Its 7/8 inch width and 0.034 inch thickness keep the product suited to many panel-based applications where an installer wants a workable overhang for trimming and a veneer thickness that can take light profiling after installation.

The 250 foot roll length and wood veneer construction make this product useful on cabinetry, shelving, and similar woodworking projects where repeated use of the same cherry appearance is needed over multiple linear feet of exposed edges.

Details That Support Consistent Cherry Edge Results

The pre-glued backing on this cherry edgebanding means adhesive is applied at the factory, so during use an installer activates that glue while pressing the veneer into place, which can create an efficient, repeatable motion along each edge.

The 0.034 inch thickness works with that pre-glued layer to build a controlled edge profile once bonded, helping the veneer sit securely on the substrate while still allowing trimming tools to cut cleanly without excessive material removal.

The 7/8 inch width contributes to repeatability because it functions across many typical panel thicknesses, giving crews a consistent band size to stock and apply on different components within the same cherry project.

The 250 foot roll length further aids consistency, since long runs of edge work can rely on the same roll, supporting uniform color and grain look from one cabinet or panel to the next wherever this cherry edgebanding is used.

Common Questions About This Cherry Edgebanding

Select This Cherry Edgebanding For Veneer Edge Runs

This FormWood wood veneer edgebanding in cherry, specified at 0.034 inch thick, 7/8 inch wide, and 250 feet long, provides a defined set of dimensions that suit cabinet and furniture edge work using a cherry veneer face.

The pre-glued backing turns the PGCHE7/8 roll into a heat-activated solution, so edge finishing and bonding occur in one pass along the workpiece, which supports straightforward workflows on cherry-based projects.

For projects calling for cherry-faced panels and consistent cherry edges, this wood veneer edgebanding offers a clearly described size and construction profile for planning edge finishing runs.