Hickory Hardware Tranquility Pull 3" (76 mm) Center to Center, White/Bright Brass, P796-W

Hickory Hardware Tranquility Series Pull For Cabinets

Hickory Hardware Tranquility Series pull gives you a 3 inch center to center handle that lines up with standard cabinet drilling, so you can swap or plan new fronts without changing hole spacing. The pull is built from zinc die cast material, which provides a solid metal feel and dependable rigidity once mounted on doors or drawers. Its white/bright brass finish combines a clean painted surface with a warm metallic accent, creating a contrast that works on both light and dark cabinetry. With a 5 inch length, the pull spans a good portion of typical drawer fronts, improving grip and finger clearance across the handle. A 1-1/8 inch projection brings the pull out from the face just enough for comfortable reach, while staying tight to the cabinet line to avoid catching clothing as people move past the run.

Key Tranquility Series Pull Details In Practice

• The 3 inch center to center dimension matches a common drilling pattern, which simplifies layout on new cabinet work and makes direct replacement straightforward on existing cabinet fronts.
• The 5 inch length or diameter measurement gives the pull a broader handhold, which helps users get a secure grip on wider drawers and heavier doors during everyday operation.
• The 1-1/8 inch projection sets the pull away from the cabinet face, creating consistent finger room while still keeping hardware close to the surface for a neat, low-profile appearance.
• The 5/8 inch width balances well with the overall length, so the pull looks proportional on standard cabinet rails and stiles while still feeling comfortable under the fingers.
• The white/bright brass finish defines the visual character of the pull, letting it act as a two-tone design element that ties painted cabinetry to brass hinges or other bright brass hardware.
• The 8-32 screw size specification matches a widely used cabinet thread, which supports straightforward installation into typical drawer fronts and door rails prepared for this thread standard.

Installation Dimensions And Mounting Fit

The 3 inch center to center drilling dimension on this Belwith Keeler cabinet pull P796-W determines where mounting holes land on the cabinet face, so installers can lay out or reuse 3 inch spaced holes without reworking the panel. Its 5 inch overall length gives a clear visual reference when aligning multiple pulls along a drawer bank, helping keep hardware runs straight and consistent. The 1-1/8 inch projection controls how far the hand moves away from the cabinet front, which affects user comfort and clearance when opening doors next to adjacent walls or appliances. With a 5/8 inch width, the pull seats comfortably on narrow rails while still presenting enough surface for a positive grip during repeated daily use.

How This White Bright Brass Pull Works On Jobs

Using The Pull On Cabinets And Drawers

This white bright brass cabinet pull fits into the Tranquility Series family, so it carries a coordinated look across doors and drawers in the same run. The specified 3 inch center to center layout matches many existing residential and light commercial cabinets, allowing this pull to step in where a 3 inch handle is already planned. The 5 inch overall length lines up visually with typical drawer widths, helping hardware read as intentional rather than undersized. Its zinc die cast construction gives each pull enough mass to feel substantial in the hand, which matters on frequently used doors such as kitchen base cabinets. The white/bright brass finish lets the pull function as a transition piece between painted cabinet faces and bright brass hinges or other bright brass components in the room.

Details That Support Consistent Hardware Results

The 3 inch center to center cabinet pull dimension simplifies jig setup because installers can reference one standard spacing across the entire project. That same spacing also supports straightforward replacement of older 3 inch pulls, maintaining existing drilling and avoiding extra filling and refinishing work. The 1-1/8 inch projection keeps the grip zone predictable from drawer to drawer, so users experience the same hand clearance on every piece. With a 5/8 inch width and 5 inch length, the pull presents a stable footprint against the cabinet surface, which helps distribute hand forces during opening and closing. The zinc die cast material supports precise shaping of the Tranquility Series profile, so pulls line up cleanly when installed in rows. The white/bright brass finish creates a defined edge between pull and cabinet face, helping installers visually align hardware by eye during final fitting.

Common Questions About This Tranquility Series Pull

Selecting This Pull For Your Cabinet Project

This zinc die cast cabinet pull combines a 3 inch center to center layout, 5 inch overall length, and 1-1/8 inch projection, giving you defined dimensions to plan drilling and alignment. The white/bright brass finish ties into Tranquility Series styling while coordinating with bright brass details across the room. By matching projects that call for 3 inch spacing and this color combination, this Belwith Keeler cabinet pull P796-W lets you standardize hardware runs with consistent grip, appearance, and mounting details.