
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
This Quickscrews #8 x 2" flat head assembly screw is built for the span that shows up constantly in cabinet and casework production: enough reach to pull two 3/4-inch panels together with thread to spare, or to seat solidly through face-frame stock into a cabinet side. The double auger point, coarse thread with nibs, and combo Square/Phillips drive are chosen for high-volume shop work where installation speed and a clean flush finish both matter.
Two inches is a workhorse length in cabinet and casework construction. Through 3/4-inch panel stock it delivers roughly 1-1/4 inches of thread engagement into the mating piece, which is the standard target for solid box joints. It also handles dado-and-rabbet carcass assembly where the screw passes through the panel and bites into a shelf or stretcher, and it works well for attaching wood subtops, hanging rails, and back panel cleats where a shorter screw would not reach the framing beneath. Cabinet shops building frameless boxes, carpenters assembling site-built casework, and installers reinforcing RTA components all reach for this length repeatedly through the course of a project.
The double auger point brings two flutes to the tip instead of one, which clears chips in two directions simultaneously. In practice this means less resistance as the screw starts in dense or slightly resinous wood, and fewer pauses to clear the hole before the thread engages. Once the thread is running, the coarse pitch pulls the joint closed efficiently. As the flat head approaches the surface, the nibs on the underside begin milling the countersink, removing material ahead of the head rather than simply displacing it. The result is a flush seat in solid wood, plywood, and most cabinet-grade sheet goods without a pre-countersink pass. The lubricated finish works across all of this, reducing the friction load on the driver and on the screw shank throughout the full 2-inch run.
Cabinet shops running production boxes through a line will find the 4,000-piece count and the combo drive combination practical: operators on a line are not all using the same bit, and the Square/Phillips recess accommodates both without a changeover. The square recess is designed to hold the screw on a correctly sized bit for one-handed placement, which matters when both hands are holding a panel in position. Custom cabinet builders and trim carpenters doing finish work on-site benefit from the nibs, which keep the head flush without extra tool passes in hardwood or hardwood plywood. The coarse thread keeps this screw in its lane: solid lumber, softwood and hardwood plywood, MDF, and particleboard. For metal or pre-tapped hardware, a machine screw is the right call instead.
The combination recess accepts a #2 square (Robertson) bit or a #2 Phillips bit. Either works in the same head, so you do not need to change drivers between operators or setups.
In most wood-based panel materials, the nibs on the underside of the flat head will mill their own countersink as the screw seats. In very hard solid hardwoods a light countersink pass may help, but in plywood, softwood, MDF, and particleboard the nibs typically seat the head flush without a separate step.
A standard Type 17 point has one longitudinal flute. The double auger point has two opposing flutes, which clears chips in both directions simultaneously. This reduces start resistance and lowers the torque needed to initiate thread engagement, particularly in dense or resinous wood.
The coarse thread on this screw is optimized for softwood, plywood, MDF, and particleboard. For hardwood face-frame joinery in maple, oak, or cherry, a fine-thread face-frame screw is the better choice because the finer pitch grips hardwood fiber without splitting the stock.
This screw carries a lubricated finish intended for interior cabinet and woodworking assembly. It is not rated for exterior exposure or contact with ACQ pressure-treated lumber. For those applications, choose a screw with a corrosion-resistant coating such as hot-dip galvanized or a manufacturer-rated exterior finish.
When the screw count, the length, and the drive are all right for the job, assembly moves without interruption. This 2-inch Quickscrews flat head covers the most common panel-thickness span in cabinet production, backed by enough volume to run a serious shop day without reaching for another box.
Sold In: 4000 Each